开云体育

I have one of these. It originally came with a simple, four button hand controller. You had to be next to the Gemini CPU to actually read anything on the LED, while simultaneously ducking, as soon you

You almost certainly burnt out the motor encoders or decoders – there may be other damage as well resulting from 12-18V getting into the 5V circuits. Where are you based? That determines the choice

You may want to contact Micheal Herman...he's the go to guy for Gemini repairs.?? You can reach him at Michael Herman <mherman346@...>? As an aside I just noticed in your that he picture

Well I did it. I inadvertently used the wrong cables for the motors and smoked something. I used 6 pin RJ connectors instead of 8 pin RJ connectors. The display was working fine until I pressed a

Totally agree with Paul. ? Put in a new battery, reset the Gemini power off and put in all Gemini 1 info, ?via Gemini ASCOM or by HC. ? ?Shut it down and re-boot it should be ok from there!

The very first thing to check is to turn off Gemini, open it, take out the 3v battery, leave it out for a minute or two, then replace it with a fresh battery. I'd also check the HC cable and

My Gemini 1 Is not working. I could get it to boot, start, and initially slew, but then the screen goes blank and is unresponsive. Same thing with different hand controllers used. Then recently

Hi there, Look at the following URLs: https://onstep.groups.io/g/main/topic/losmandy_g11_onstep/82492966 https://www.terransindustry.com/collections/onstep-v4-kit

Replacing the battery is pretty simple and after doing so you just need to re-enter your customisations (location, time etc.). David Sent: 12 March 2025 16:25 To: [email protected] Subject: Re:

There’s also the caveat that the support for shaft encoders may not be present in the Gemini-2 code. It was in the Gemini-1, but given how few of the Losmandy DSCH (their own shaft encoders) were

I don’t believe there are any high precision encoders that are compatible with the Gemini system, but I could be wrong. I was looking at the Renishaw high precision absolute encoders but Scott

That would mean that there's an issue with Gemini itself, possibly a connection issue from the DIN connector to the PCB, or with one of the servo controller chips. There are some repairers that work

Hi Paul, thank you so much for your response. Fortunately I happen to have a spare Gemini 1, I tried using that one with the mount and the motors seem to be working OK, so the problem must be within

On Wed, Mar 12, 2025 at 11:24 AM, <francomeconi@...> wrote: > > As soon as I powered up the mount the RA motor started slewing at a very > high speed, I had to almost immediately shut down the

Hi all! I'm new to the group. I recently bought a Losmandy G11 running on Gemini 1 v1.04 from a friend. I've been setting it up and trying to configure it with NINA. I'd been having issues with the

I'm curious to know more about the encoder port use. Is the intended use to add an external encoder to improve RA or DEC guiding? If this is correct, are there any products available to support high

Hi Paul, As one of first Losmandy mount users in Japan, I really enjoyed this article. I recall I imported a CG-11 for my C11 in 1993.? The mount, which had 492 Digital Drive system, was initilaly

Rene,/Paul/David have done a huge amount of great work and I applaud them. ? ?David completely re-wrote the Motor control dsPICC33 firmware, Paul has been constantly improving Gemini ASCOM and GFU

Hi All, Please enjoy a brief history of the past quarter-century narrated by our own René : https://gemini-2.com/Gemini25Years.html Happy Birthday, Gemini! -Paul