开云体育

Hi Greg, I had a 914S 2.0l which was a terrible car in most ways other than the quality of life while in the driver's seat speeding through Mulholland canyon, on the 110 and Angeles Crest highway. I

Darned right, Chip. I was thinking the same thing. I don’t have a Turbo, but my Cayman S is very entertaining and gangs of fun for autocross (which I do a lot). It’s a different kind of fun from

Which car to take to the corner store largely depends on where the corner store you want to go to is located.??Have you driven a twin turbo Porsche?? The saying "Porsche, there is no substitute"

Thanks, folks! MH and I have already "talked" and I'll be sending the unit to him for repair. I do like this particular Gemini because all the connections echo the 492 drives I have on my four other

As others have said. ?It’ll be the motor (encoder pickup) or mainboard encoder read ICs PLDs. ? ? If you put Ra motor on DEC and it comes good. ?Then it’s a motor or cable issue. You don’t

On Wed, Mar 12, 2025 at 08:24 AM, Franco Meconi wrote: > > Hi all! I'm new to the group. I recently bought a Losmandy G11 running on > Gemini 1 v1.04 from a friend. I've been setting it up and

LOL, I am sure that Brendan would replace the offending green LED with an appropriate red LED of Warren asked him to. -- Chip Louie Chief Daydreamer Imagination Hardware Astrospheric - South

Hi Warren, Rene and the others here are right, the first generation Gemini controllers are an elegant solution at the advent of amateur astronomy's move to mechanisation and automation.? It was a

I have two of the original gemini 1 's 4 buttons on one side and no screen on the other side Of the hand controllerSent from my Galaxy

Warren. ?I cannot see anything obvious but I’d be looking at the two motor encoder PLD ICs (top right, Encoder 5V ) and D10/D9 dual diodes in sot23-3 package (bottom left, 5V lines). This is fully

Paul, Don't duck! There are screws to tilt the board upwards ;) ROTFL 8) Also,? you can use the DeLuxe in parallel and get the information twice? 8) René Am 07.04.25 um 22:18 schrieb Paul

This was my original design. Aveox soldered the green power LED instead of the red one onto it because their rules said that power LEDs have to be green, night vision wasn't that important

If you're willing to invest the money, you should consider sending the mount to Losmandy and upgrading to Gemini II, tune up and perhaps tucked motors. I did this with my old Losmandy and I have no

I have one of these. It originally came with a simple, four button hand controller. You had to be next to the Gemini CPU to actually read anything on the LED, while simultaneously ducking, as soon you

You almost certainly burnt out the motor encoders or decoders – there may be other damage as well resulting from 12-18V getting into the 5V circuits. Where are you based? That determines the

You may want to contact Micheal Herman...he's the go to guy for Gemini repairs.?? You can reach him at Michael Herman <mherman346@...>? As an aside I just noticed in your that he picture

Well I did it. I inadvertently used the wrong cables for the motors and smoked something. I used 6 pin RJ connectors instead of 8 pin RJ connectors. The display was working fine until I pressed a

Totally agree with Paul. ? Put in a new battery, reset the Gemini power off and put in all Gemini 1 info, ?via Gemini ASCOM or by HC. ? ?Shut it down and re-boot it should be ok from

The very first thing to check is to turn off Gemini, open it, take out the 3v battery, leave it out for a minute or two, then replace it with a fresh battery. I'd also check the HC cable and

My Gemini 1 Is not working. I could get it to boot, start, and initially slew, but then the screen goes blank and is unresponsive. Same thing with different hand controllers used. Then recently