开云体育

An alternative is to use a straight USB cable from PC to Gemini connected to the USB B (device) input on Gemini. With modern versions of Windows (10 or 11), this will automatically install a driver

If you wish to continue using serial, you need a cable from the serial port on the computer to a 6P6C modular connector. For the G1 you used a 4P4C connector wired thus: Computer 4P4C GND -> Pin 2, Tx

I used The Sky 6 to do go-tos by connecting the Gemini I to my computer via a serial to USB connection.? How do I accomplish this with the Gemini 2? I still have the USB cable,? but need to know

On Mon, Oct 21, 2024 at 06:50 PM, David C. Partridge wrote: > > > > That Slate-AX sounds great apart from the USB-C port for power.?? I have > 12V DC barrel connectors on my power box but nothing

Thanks Paul. Regards Steve

David, I don't know if you're still looking for suggestions, but if you have A/C power in your observatory, this might be an option for you:

Correct, it they are not travel routers but OP didn't mention that in his original post.. He asked for a AP that can Extend his Wi-Fi w/o running a cable and mentions 12v power as a must, or

Sure but AFAIK there are no nano or mini travel routers produced by Linksys and they are not the size of a deck of cards.? Additionally the Slate-AX is a full featured router and has all modern

Linksys routers use 12v 5.1x2.1 connections. They're about the same price as the GL.iNet GL-AXT1800 but they have more ports and can be used as an AP, or an extender/repeater etc...

The issue has been diagnosed and hopefully resolved :) The return value of the :Sc command (added in L5.3) was incorrectly interpreted by the ASCOM driver (it expected a # character at the end). That

Hi Tom, This sounds like you had some hardware/electrical failure. Gemini doesn't go into boot loop unless it's power cycled or a serious error has occurred. Your USB hub failing could be related (or,

No, not really.? I'm on L6.05beta and HC 1.63cbeta and I have used it quite a bit with the HC for visual and left it running with ASIAIR Plus 256 v3 and the

I think this was correct under very specific conditions.? I remembered the 2-speed speed up worked with the settings I used and the all speed speed up happened only worked if you held down the

The DHCP setting are 6 sec and not-checked (off or no DHCP).? I am set static with no patch cable connected to the unit. The same settings were applied during production, and the issue did not arise

Ooh... Glad you caught that. I use the variable output of my PPBA set to 5 VDC. Sorry about that. I completely forgot. Regards, Joel

Turning off Set Time on connect allowed a perfectly good connection. All working normally AFAICT. This is *most* odd. I wonder how the Sc command isn’t working (over serial port) for EITHER of the

Yes it was! Seems that your Gemini doesn't like setting UTC time. The result of the command isn't received 10 seconds after the command was issued (I actually increased the serial timeouts in the

Paul, the entire log file was in the attachment to the earlier message. The Firmware was 6.05 D. Sent: 25 October 2024 21:10 To: [email protected] Subject: Re: [Gemini-II_io] Serial connection to G2

I’ve noticed 9600bps laggy with Gemini ASCOM. I use 57,600bps on BT and it’s much more snappier. ? I get GEMINI settings pop up in ASCOM almost immediately. At 9600 I’ve seen it take quite a

I recently had my Gemini 2 upgraded to L6 by Losmandy. Set it up yesterday. Had the scope parked but on for an hour or two. Walked away from it. When I came back, the hand controller was in a boot