开云体育

Its the slash in the callsign that's causing trouble. If you attempt a lookup of OY/DD1LD via the QRZ.com site, it performs a lookup on DD1LD. I'll extend Pathfinder to emulate this behavior.

I am trying to set up my old PK-232 in Warbler and not having much success. The PK-232 works fine with N1MM and Logic, but I have tried every combination of speed, parity and stop bit to little

For various reasons, usually copy/paste, a lot of the First Names in the Name Column have a Lower Case letter. Usually it's how the person sent it in PSK mode. Or my too lazy to hit the Caps Key when

I can confirm this behavior ... enabling "memory banks" display - which I have never used - causes the A and B buttons and "dual receive" box to start flashing. It also causes Commander to

George, The fldigi to DXLab Bridge is available from N2AMG: The update or full version can be downloaded from http://www.n2amg.com Information on removing a password from the LotW certificate

Cliff You have have got it. Hopefully if this is the case Dave can build in some timeout or failsafe. Bob

I should have finished the last note with the fact that this has happened Danny Douglas N7DC ex WN5QMX ET2US WA5UKR ET3USA SV0WPP VS6DD N7DC/YV5 G5CTB All 2 years or more (except Novice). Short stints

If you do a manual lookup on OD5ET, you will notice that there are Arabic characters in the name field. Perhaps that is causing the problem. 73, Cliff K3LL Sent: Friday, December 04, 2009

Hi Dave Here is a good one QRZ subscription works on all calls tired except one. If I put in OD5ET and click the RST box in the DXkeeper Capture window it goes away and doesn't come back.

I have a master and several “slave” computers. I created a .bat file (remember those?) called GO.BAT which contains the following commands: xcopy "c:\program files\dxlab

Every time that I double click on a spot on SC, I get the window "Callbook error Required version of Pathfinder not running". Have closed both PF and SC a couple or more times, and both are showing

Anyone see this problem... Had DXKeeper lockup and become unresponsive when entering a contact into the capture window. Did not time out and had to reboot to fix it. After playing around it appears

Dave, is there bridge software so that FLDIGI can be used with DXLab? Also while I am here how do you get rid of the password requirement for LOTW? Thanks, George W2GS

It is now 14:27 UTC, 4 December 2009 - I'm getting the blinking as well. Rig is K3 interfaced via RS232 jack COM1 Commander 8.0.9 Filters and Devices "window" open - no flashing Engaged "Memory

Phil, I use a similar technique, by sharing the folder across the network. I can use a copy of DXK on a separate machine, with the database specified on that mounted drive. I actually found it

Hello all, I know this has been asked before, but I can't find the email I wanted in the files. What I would like is to be able to access my log file from another PC. I have DXK installed (and

Well, mine does not. It has the connector but it is not active. I cannot replace the drive as it is rente3d form Charter. Gil Rochester ,MN W0MN ICC and twitter WzeroMN 44.082036N 92.513219W 1050'

On one of my other forums (I think it's the N1MM forum) there have been numerous comments that when purchasing a USB to Serial converter, look for one with the FTDI chipset. Art - N4PJ

I noted that some time ago. But when I hand typed the call in the qrz page, the correct call would come up. Danny Douglas N7DC ex WN5QMX ET2US WA5UKR ET3USA SV0WPP VS6DD N7DC/YV5 G5CTB All 2 years

I found quite a few 1 TB drives for $100 or less, but many (most!) of 'em couldn't do SATA. I also didn't have to pay any shipping! In addition to the amount of disk storage, I couldn't believe the