开云体育

Dave, Below is screen shot of the Audio Alarm Tab from Spot Collectors Config window: [image: image.png] I get sounds when I press the sound buttons under the Sound Files Section of the Tab. 73, Dick

+ AA6YQ comments below + On the General tab of DXView's Configuration window, specify your latitude and longitude in the QTH panel. Then terminate DXView and direct the Launcher to update your

I have set myQTH and saved it to my workspace.? After shutting everything down and restarting with the correct workspace DX Keeper shows myQTH correctly.? The problem is DXView shows a different

+ AA6YQ comments below 1a. what CI-V address have you specified in the Radio panel ? IC-7100 and 88 hex address 1b. in the PTT panel, with the radio connected to an antenna on a clear amateur

+ AA6YQ comments below My "New Marathon" announcement/alarm has stopped working. I believe I have all my sound settings working OK - other audio seems to come through the speakers OK. I believe it may

Dave, all, My "New Marathon" announcement/alarm has stopped working. I believe I have all my sound settings working OK - other audio seems to come through the speakers OK. I believe it may be

+ AA6YQ comments below + What's an example of a pair of identical QSOs whose callsigns, bands, modes, and begin times are identical, but don't have their Select items set to 'Y' after invoking the

I have filtered the log for qsos just in 2024. If I run the entire log there are more than 200k qsos and that will take too long. On the advanced tab, I set duplicates range to 0, I do not select

Will do. Thanks Dave. 73 de AB2UL - Tom

Hi Dave, 1a. what CI-V address have you specified in the Radio panel ? *IC-7100 and 88 hex address* 1b. in the PTT panel, with the radio connected to an antenna on a clear amateur frequency, do the TX

+ AA6YQ comments below + When LoTW returns to reliable service, you can use DXKeeper's "Sync LoTW QSOs" "Sync LoTW QSLs" functions to update all logged QSOs to reflect their acceptance? and

+ AA6YQ comment sbelow + Great! Some questions: 1. on the Configuration window's General tab, 1a. what CI-V address have you specified in the Radio panel ? 1b. in the PTT panel, with the radio

Hi Dave, Many thanks for your advice. It works now. Best regards, Georges F6DFZ

I have already used the bulk modifying method on my log, it works... Related to this. As I mentioned before I previously used XMLog. I exported my adif log from that and imported it into DXKeeper. I

+ AA6YQ comments below + This article describes option to make the text on your monitor easier to read: https://www.dxlabsuite.com/dxlabwiki/MonitorsForOldEyes + When searching for information in

Thanks Dave, That is what I was looking for.? I don't know why I couldn't find it.? Probably the same reason I missed importing with the wrong QTH, etc.? I'm getting old and can't see. Thanks

+ AA6YQ comments below + Due to insufficient documentation and Xiegu declining to provide a loander, Commander does not support the G106. + In the "Primary CAT Serial Port" panel on the Configuration

+ AA6YQ comments below I know there is a way to correct my mistake, but I can't seem to figure out how. I imported about 120 QSO's using an ADIF file, but........... I didn't realize I had MyQTH for

Hi to the group, I am trying to configure this combo with Commander. I use IC-7100, address 88, Com port 7, Baud rate 19200. I have a Multi radio configuration with my IC-7300, which works flawlessly.

I know there is a way to correct my mistake, but I can't seem to figure out how. I imported about 120 QSO's using an ADIF file, but...........? I didn't realize I had MyQTH for the wrong location and