Does anyone else with an FT-1000D see Commander reporting the
transceiver to be in RTTY-R on some bands but RTTY on other bands?
The frequency/mode reports are the same for the FT-1000D, FT-1000MP,
Mark V, etc. I have never seen RTTY-R on some bands and not others
with the Mark V. I think I'd start by clearing the memories/CPU of
the FT-1000D.
73,
... Joe, W4TV
-----Original Message-----
From: dxlab@... [mailto:dxlab@...] On
Behalf Of Dave Bernstein
Sent: Monday, November 12, 2007 8:03 PM
To: dxlab@...
Subject: [dxlab] Re: Commander and FT-1000D
That's very puzzling indeed, Wolf.
Does anyone else with an FT-1000D see Commander reporting the
transceiver to be in RTTY-R on some bands but RTTY on other bands?
73,
Dave, AA6YQ
--- In dxlab@..., "Wolf, DK1FW" <dk1fw@...> wrote:
Dave,
I have now set the WW Mode Control Panel to have WW go to RTTY for
both
RTTY and RTTY-R at the Transceiver (Commander) side.
WW now follows my mode selection on the FT-1000D on all bands.
No problem here.
On the FT-1000D you can either select RTTY/LSB (normal) or RTTY/USB
(reverse).
I assume RTTY/USB should correspond to what you call RTTY-R in
DXLab.
When the FT-1000D is in RTTY/LSB Commander indicates RTTY-R on
20m/30m/80m and RTTY on all other bands.
When I change from RTTY/LSB to RTTY/USB Commander does not change
the
RTTY mode on any band.
When commanding RTTY from WW the FT-1000D is always put to RTTY/LSB
as
it should.
(I have selected FSK RTTY in the RTTY Operating Mode Panel)
However, Commander reports RTTY-R on 20/30/80m
I have operated RTTY on all bands recently and never got any
reports of
being inverted.
Leaves me puzzeled.
73 de Wolf, DK1FW
Dave Bernstein schrieb:
Commander is just reporting the transceiver mode, Wolf. WinWarbler
places the transceiver into a specified mode when you set
its "Operating Mode" panel to RTTY, but only one such transceiver
mode can be specified -- it can't be configured to place the
transceiver into RTTY on some bands and into RTTY-R on others.
So the questions are
"why is your FT1000D using RTTY-R on some bands and RTTY on the
others?"
"Aren't you upside down when operating RTTY on some bands?"
73,
Dave, AA6YQ
--- In dxlab@... <mailto:dxlab%
40yahoogroups.com>, "Wolf,
DK1FW" <dk1fw@> wrote:
With the new Mode Selection feature in WW 546 I realised that WW
did not
follow RTTY mode selction on the FT-1000D on 20m and 30m.
Mode Selecton Panel was set for CW=CW, USB/LSB=FONE, RTTY=RTTY.
When checking COMMANDER, which is normally minimized in my
setup, I
found that contrary to all other bands Commander shows FT-1000D
RTTY as
RTTY-R on 20m and 30m.
On the other bands it shows FT-1000D RTTY as RTTY.
I seem to have overlooked that, when I checked the Commander
version for
the FT-1000D, which Dave sent me some time ago.
Meanwhile setting RTTY-R=RTTY in WinWarbler in the WW Mode
Selection
Panel is a viable work-around.
73 de Wolf, DK1FW
Yahoo! Groups Links
