¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io

Re: QSL Labels or Cards


 

Please direct DXKeeper to generate a print preview of a QSL card. Make a screen shot of the print preview, attach it to an email message, and send it to me via



aa6yq (at) ambersoft.com



73,



Dave, 8P9RY





From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 6:12 PM
To: dxlab@...
Subject: Re: [dxlab] QSL Labels or Cards





So here is my settings:




I have not gotten this to work...
When I try to print, I see the wrong paper size!


Will WC2L

On 3/5/2016 3:24 PM, 'Dave AA6YQ' aa6yq@... [dxlab] wrote:

The screen shot in

<> <>

Shows typical settings for printing cards "4 up". As a starting point, select a paper size that is larger than what's needed in both dimensions.

73,

Dave, AA6YQ


-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 3:17 PM
To: dxlab@...
Subject: Re: [dxlab] QSL Labels or Cards

That fixes the label. I thought had checked it. I also tried it in the printer.

Now to figure out how to print on cards.
Will WC2L

On 3/5/2016 3:05 PM, 'Dave AA6YQ' aa6yq@... [dxlab] wrote:

Did you change the setting in the ¡°Single Label Orientation¡± panel as suggested?



73,



Dave, AA6YQ



From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 2:57 PM
To: dxlab@...
Subject: Re: [dxlab] QSL Labels or Cards






SO with Single label selected.
Printer set to Landscape or Portrait Printing If I set it for Height
1.1 and Width 3.2 I get "Specified column 1 offset is too larg (maximum is -2.203472 inches)" The view is still wrong. It shows the printing as horizontal. The label is shown as vertical.
If I set it for Height 3.2 and Width 1.1 I get I don't get a message. The view is still wrong. It shows the printing as horizontal. The label is shown as vertical.


SO no matter how I set it up, it fails to print correctly.

Select QSL Card:
I found a driver that seems to appear to work in other programs and gives me the QSL Card as an option. Card is setup as Width 3.5 Height 5.5. I have the printer selected, the sized selected and source selected in QSL configuration - Printer.

I have Printer QSL Cards and preview checked, I get "Specified QSL Card width is too small" essage. When the preview starts up, it Width at 10.653 x Length 8.152.

Since I can't get the DXKeeper to print labels correctly, I am guessing cards are going to be the same issue....

Will WC2L

On 3/5/2016 12:54 PM, 'Dave AA6YQ' aa6yq@... [dxlab] wrote:

AA6YQ comments below


-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 12:31 PM
To: ' Dave AA6YQ' aa6yq@... [dxlab]
Subject: [dxlab] QSL Labels or Cards

I was trying to get a few cards and or labels done.
When I preview a single label, it always shows the printing as horizontal. The label is shown as vertical. The printer is a Dymo LabelWriter 450.


In the "QSL labels and address labels" panel on the "QSL Configuration" window's Printer tab, change the setting in the "Single- Label Orientation" sub-panel.


I don't see the Avery 4150 as an option (labels I have).


That's a function of your printer driver.



With printing directly on the cards, it does not see the custom paper type I have added to the print engine.


That's a function of your printer driver.



If I select 3x5, all I get is different error messages depending on what I choose. I am using a Brother HL-5250dn.


Without knowing what the error messages say, one can only guess: try selecting a larger paper size.


73,

Dave, AA6YQ



------------------------------------
Posted by: "Dave AA6YQ" <mailto:aa6yq@...> <mailto:aa6yq@...>
<mailto:aa6yq@...> <aa6yq@...>
------------------------------------


------------------------------------

Yahoo Groups Links











--
William Liporace WC2L
or AR-Cluster Node telent dxc.wc22l.com or 144.93 MHz wc2l@...



------------------------------------
Posted by: William Liporace <mailto:wc2l@...> <wc2l@...>
------------------------------------


------------------------------------

Yahoo Groups Links






------------------------------------
Posted by: "Dave AA6YQ" <mailto:aa6yq@...> <aa6yq@...>
------------------------------------


------------------------------------

Yahoo Groups Links









--
William Liporace WC2L
or
AR-Cluster Node telent dxc.wc22l.com or 144.93 MHz
wc2l@...










[Non-text portions of this message have been removed]

Join [email protected] to automatically receive all group messages.