开云体育

The plate chokes in my L7 are copper with a coating of some type but can be soldered well. I have not put the Metal Oxide resistors on them yet and still using amp at a lower power level that is

Hi Mark, I tried jumping in there Sunday afternoon but conditions were terrible, I could barely hear you here in Massachusetts. Hopefully things will be better next week. I was running my "B" line by

Not so sure of this. I think aluminum can be soldered using aluminum solder and a flux like borax. A problem with aluminum is that pure aluminum develops a layer of oxide almost immediately. The layer

You can't solder aluminum anyway.

Yesterdays net was held on 7.238?@ 4pm Eastern. We had a total of 27 check-ins. The following list of radio's were used: TWINS = 4 TR3 = 1 TR4(x) = 9 TR4 = 2 TR7 = 6 Our net control for next week

Message /g/DRAKE-RADIO/message/77423 . "K6OXN Bob via groups.io" <bobk6oxn@...> wrote: -- 73 -Jim NU0C

I did not see the referral for that article but have now studied it and think I might use the MOF resistors I have. I have several 100 ohm 5 watt resistors, I think I will place in my L7 and see how

Did you read this link that I posted previously? https://amfone.net/Amforum/index.php?topic=45450.0 "K6OXN Bob via groups.io" <bobk6oxn@...> wrote: -- 73 -Jim NU0C

would the newer metal oxide film resistors rated at 5 watts be a better replacement for the old carbon resistors?? I am looking at replacing the 47 ohm carbon 2 watt resistors in my L7 with 47 ohm 5

##? read it several times, eons ago.? I have two FT-1000D's.? Basically, before u turn the RF clipper on,? you 1st adjust the mic gain for XXX? alc action.? ?Trying to maintain XXX? alc action

##? Nope.? I bought a behringer 9024? 6 x band digital compressor.? Rack mount. I had 3 of em at one point.? The 6 x bands are nose to tail, no gaps....and a max of 20 hz to 20 khz. For ham radio

I can understand that. While I'm not that old, after working for close to 40 years; I'd like to retire. I tried calling the tech support/parts ordering line several times today. No one answered. So, I

I remember when some had a fit about implementing SSB over AM. It was considered the radio mode destroyer but we got through it. Which Drake model had the best AM modulation?

ALC was never intended to be a speech processing system. Undesirable things happen when you try to do that. I point (again) to SM5BSZ's work in this. https://www.sm5bsz.com/dynrange/alc.htm 73 -Jim

Use the service manual test point. That is what the alignment of the rest of the radio is based on. 73 -Jim NU0C "Bill NZ0T via groups.io" <nz0tham@...> wrote:

Did anyone consider that the man is just plain tired? Heck after 52+ years in the business, and? 80+ years old. Let's face it there are more years behind all or almost all of us than ahead.And don't

The Drake station has been spoken for. Thanks for all the interest Tim? K?FL

*** I have to concur. Honestly, I'm surprised it still exists at all. I just don't hear much happening on the bands, except for contests. I miss the 70's. The novice bands were solid CW from one end

Yes shrinking.? Halve the new people with licenses are not into ham radio and don't even own a radio.? I asked one guy, what was his call.? He had to get the license out of his wallet in order to

“Preppers” and new licensees aren’t using traditional products. I stand by my comments. Steve Wedge, W1ES/4 Time flies like an arrow. Fruit flies like a banana. Sent from [Proton