开云体育

Have you considered just running dual antennas? Vertical separation at 23cm is not much.

I once retuned a 800 MHz TX/RX duplexer to 23cm by removing the tuning plunger and cutting off the outer fingers. Then I used a fine hacksaw to cut new fingers and reinstalling the inner

Good evening, Anyone in the Houston area using 23cm? I recently got a 9700 and would like test and/or get on a net. Michael KD5DFB

I have tuned up several 400 MHz duplexers on 1290 MHz. No mods, just tuning. Start my tuning up the duplexer in the 400 MHz band. Say your output is 1290 MHz? ? Tune up one side of cavities on 430

Does anyone have a 23cm duplexer available? Or maybe instructions for converting a 70cm?Sinclair Q3220E to 23cm, I have several to use? I have this ICOM ID-PI1200VD sitting here that I'd like to get

hi i just purchased a icom id-1 have software but my issue is the computer does not recognize the the usb cable on the icom radio im using windows 7 on my laptop how cani factory reset radio and my

Hi Ken I have adjusted frequency on an IC-2820H and ID-5100 that also drifted low in frequency after more than 10 years of aging. The method used for those is found in each radio service manual

I am interested in this too.? I imagine it is a relatively common issue with an old radio. Last year I contacted someone in the US who works on ICOM stuff - without success. They had no such

Hello. I'm looking for ID-1 Adjustment Software CD so if you have come across that CD then please let me know. I have the ID-1 Control Software ISO and attached it here for you.

Hi, An amateur colleague has an Icom -ID-1 23 cm FM/DSTAR transceiver and has discovered that it is off frequency and needs adjustment. The way to do the adjustment like the frequency is to use the

HRO Icom IC-905 Special ICOM IC-905 New Year Special This is a Special Limited Time opportunity 12-29-2023 through 3-31-2024 on the ICOM IC-905 VHF, UHF, SHF Microwave Transceiver and ALL

IARU President Interviewed at ITU WRC-23 | | | | | | | | | | | ITU INTERVIEWS @ WRC-23: Timothy Ellam K.C., President, The Internationa... | | |

WRC-23 Reaches Acceptable Conclusion on 23cm Issue | | | | | | | | | | | WRC-23 Reaches Acceptable Conclusion on 23 cm Issue | International Amat... | | |

Ron, I've never tried this, but there is an ID Output setting that applies "While Repeater is Stand-by" in the Analog Repeater section. Maybe that would do the self-triggered ID that you're looking

Hey Brad, how are you neighbor? Repeater started working after a full reset. Yes, saw those settings in the program. All good points. I would like to ask if there is a setting to keep the ID

Ron, We haven't experienced this issue, but I remembered that there is a setup item in the Analog Repeater menu which allows you to configure the ID Output. I just checked the KE5RCS setup by

Just purchased an ID- RP4010V with the ID-RP3 software.? After performing initial setup and just getting it going in analog mode only, the repeater does not send any Morse ID's.? All other functions

Did you receive the announcement Link Established? Then switch back to CQCQCQ on your radio?

I noticed a few interesting looking nets listed for the subject reflector so I tried to link my local gateway repeater to it to no avail.? The syntax I used was "XRF002AL"? Any thoughts on where I

As you can tell from Steve's post, we have an awesome 23cm Dstar Repeater. In addition to that asset, we also support D-Star on 70cm, DMR, Fusion, NXDN, P25, and 1.25m FM, in addition to GMRS. Please