开云体育

Limited seats are still available for D-STAR InfoCon at Dayton Hamvention for 2024 The class provides an introduction to D-STAR for new users and more advanced topics for more experienced D-STAR

Our new 440 Gen 3 module in FM would pump out a CWID every 10 minutes rain or shine.? KD8GBL managed to get the "tunnel the USB packets over IP" thing going on our controller and fixed it

You should be able to use any of the new Gen 3 repeater modules as your new controller to get the Gen 2 stack up again and sell off any spare Gen 2 modules.

Hi So the repeaters: Gen 1 – Was a white pole mount controller + 1.2 DD mode unit, and 1.2 DV add on module - 8 pin round interconnect cable Gen 2 – Rack mount RP-2D controller, range of

I just had to load these in a hurry on Windows 10 /64 bit. The newer Icom drivers work fine. I copied them off the CD download to an easy place C:/id1. You have to go into the old control panel

This is AI4UE , I like to get it and put it on air in Burlington to cover more range Peter Scherp wrote:

I have one more Gen 1 1200DV module you can have.? $50 is the shipping cost.? ?Best to have it on the air vs in my basement.

Erik, Thanks for the insight! I guess I am confused. Looking at Icom's website and HRO, it appears the current models are the Gen 3 ID-RP2010V, ID-RP4010V and IDRP1200DV. HRO has the ID-RP2010V in

We have a vast fleet of D-Star repeaters in MN. We are upgrading most voice modules to the new dual mode (+FM) hardware. Thanks Ray ? Let me ask if we have spare/take out controllers. I

Michael, I believe all of the repeaters in that generation are EOL. Our RP2C died, so all of the repeaters are out of service, and ICOM can no longer repair the RP2C. Let me know if you're

Good evening, Has anyone heard if the IDRP1200VD is EOL? Got an email back from Icom stating: "I don’t believe we sell this item anymore, and there is currently no information on whether it will

*D-STAR InfoCon is back at Dayton Hamvention for 2024* providing an introduction to D-STAR for new users and more advanced topics for more experienced D-STAR users. The class will be held at the Drury

I would love to have that module if it’s available. Already have a duplexer. Radio Rex AJ4GC

The ID-1 drivers + software can be made to work on Windows 7 and 10, 32 and 64 bits.? ? You need the newer (possibly signed) serial /USB chipset drivers.? ?Extensive searching is required.? The

We have at least one ID-RP1VS 1.2Gig? Gen1 voice repeater module available at shipping cost. ($50?)? ?These are in Minneapolis. Erik, NY9D

We bought a commercial 1.2 voice duplexer (TX/RX?) as I recall in 2008 for like $900. Alan WB0ZKB made 1.2 duplexers and triplexers out of welded 4" aluminum square tubing pieces. He made several

My experimenting is showing that it's not going to be too difficult to make a combination of notch and bandpass cavities from the 70cm?Sinclair Q3220E. Not going to try to make the combined

Sounds good.? I picked up the repeater from my storage earlier today.? I'll cobble some antennas together this weekend.? I'll let you know.

I work at I-10 and Campbell. I will plan to bring my 9700 one day and see if I can work your repeater, if it is on the air. Also, W5ZM replied to my post and said there is a repeater on 1292. The only

I have a 23cm Icom repeater I bought during the HRO "flash sale" last year.? I was going to put in on the air this week.? Not much height, so a "backyard" setup near Silber and I-10.? I'm also a