¿ªÔÆÌåÓý

Already updated to asia/manila but upon nooting this greets me. Any suggestion for proper updating?

I have a minor update to make zbitx work with wsjtx/fldigi/etc and fixed cw latency. You have to update just the raspberry zero. From a terminal window, type this: cd ~/sbitx ./update sbitx this should do it

I plugged an HDMI display into each of the micro-HDMI connectors and got no image. My HF station Pi4 easily uses two displays but, of course, no 7-inch touchscreen. What am I missing? (My bitxs are my holiday radios and the sBitX can be my transceiver AND my laptop, very nice for travel.)

To find the root cause of the spurs, I worked in 2 steps: 1. I took the front panel board out of the case and connected it with jumper wires to the main board. My objective was to eliminate possible EMI from the Pi Pico into the RF board. This did not make a difference for the spurs, as they just went down by 0.5dB which is the resolution of the TinySA. 2. In the si5351v2.c code I changed 8MA to 2MA. This results in approximately 5dBm less output power (33.5 vs 38.1dBm) but also a relative reduction of the spurs by approximately 7.5dB from -28.1dBc to -35.6dBc: Reduced output power is most probably due to the fact that the zBitx uses a diode ring mixer instead of the KISS-Mixer used in the sBitx and the oscillator power to the ring mixer is provided directly by the SI5351 CLK2 output (in reality an MS5351). Also, the IF diode ring mixer gets its oscillator signal directly from the SI5351 CLK1, whereas in the sBitx there is a buffer amplifier with two 2N3904. It could be that the much higher load on the SI5351 outputs, results in some intermodulation in the SI5351, which finally shows up as spurs. Given that these spurs are a showstopper, to transmit with the zBitx as the spurs are not at least 40dB suppressed, I am looking forward to further investigation and direction by hfsignals. On Mon, Apr 14, 2025 at 11:39 PM, Ron, N6YWU wrote: -- 73, Joerg - DB2OO

Hi I have some LiPo power packs, 2S, with various power (capacity) ratings. Some are rated for a discharge rate over 20-30 times the rated nominal capacity. I have no economic reason or interest in suggesting this, but i think that can be a smart solution to power the zbitx. Only for example, the following battery as 7.4 nominal voltage, 3600 mA capacity, size 65 x 50 x 28mm and weight 165 g. Price under 13 € Another interesting option is the hardcase batteries: this one has a capacity of 3000 mA, size 93 x 47 x 19 mm, weight 143g, and price a little more than 11€. 73 from Italy Giuseppe IU0OYC

I am not getting good results with the AGC supplied by AmateruRarioKits. I am unsure if it is a bad board (it does not have the multi-turn potentiometers shown in the documentation) or if it is the connection point to the uBitx board. The photo shows the connection to the collector of Q10. The instructions show connecting to the base across R10: I will try moving the connection and see if the performance improves. Has anyone else installed this board successfully and is happy with the results? 73 Evan AC9TU

Hi! More work following the path that Ashhar suggested. I have also bought an older Icom 810H that has full duplex VHF/UHF. I'm doing initial experiments on Windows PC, but I have already demonstrated full Doppler shift control of sBitx acting as the 10m transceiver to a transverter, so this can all move to the sBitx.... GPREDICT re-installed due to better location, tracking any satellite I like. Does all the trig and doppler MATH RIGCTLD - previously studied and working; receives tcp/ip commands from GPREDIT to do doppler shift adjustments of sBitx or Icom radio Today: ROTCTLD -- figured out how to run this on a windows machine. Receives trig output of GPREDICT. Converts (in this case) to Yaesu type rotator commands for Az/ elevation and sends out serial port (in my case, COM4, 9600 baud) K3NG Rotator Controller -- I havent made a board for this yet. So I took one of my homebrew WINKEYER ARDUINO simulators, and reprogrammed it using K3NG code to "act like" the controller, handling Az, El controls, reading the CW speed control as if it were an azimuth potentiometer; running the display and activating the "key" and "PTT" to rotate clockwise or counterclockwise. The reprogramming of my Winkeyer Arduino appeard to be a huge success. I properly set the pins to run the display, which worked FINE. It was reading the speed pot as an azimuth reading, and if I pushed "buttons" it would read different elevations. ROTCLD happily connected to it at 9600 baud, and the "rotator controller" accepted commands and displayed them. I was not able on the first test to monitor whether it activated simulated motor controls (key output, etc) -- but that will come. So huge success here and soon (days, weeks?) I should be able to lay out a board (many others have done so before me, but some just did crazy wiring between variuous "shields") to put all this in a neat little package with relay outputs, possibly with PWM output (dunno)., to control available rotators for real. 73 Gordon KX4Z