开云体育

So, I'd been watching another thread for resolution, but it may not be the same thing. Questions up front. 1. Any reason why 10m is 0W? 2. See my drive? it's 96, and I don't know why I can't get it to 100. When using the wheel, it won't go any higher, though it certainly goes lower. These lead me to believe both are software configuration related. The problem: I initially had the issue with FT8 locking up the zBitx. Updating the both the Zero and Pico software resolved that. I'm at 1.6 and 3.051 now. Running sBitx on the external monitor resulted in 0W out. However, I'd still get 0 watts out when transmitting FT8 on 10m. However, I remembered I get less output on my sBitx at 10m, so I setup a 20m vertical and I got power out. I haven't had time to check 12/15/17m. Could there be a problem with the calibration files that I absolutely did not backup when I did the update? Any guidance would be appreciated! Matt

I tried to update my sBitx but got the error message below. I checked the sbitx directory and found “oled.c” instead. Please advise how to update my sBitx V3. Thanks, Steve WE5K

Hi! More work following the path that Ashhar suggested. I have also bought an older Icom 810H that has full duplex VHF/UHF. I'm doing initial experiments on Windows PC, but I have already demonstrated full Doppler shift control of sBitx acting as the 10m transceiver to a transverter, so this can all move to the sBitx.... GPREDICT re-installed due to better location, tracking any satellite I like. Does all the trig and doppler MATH RIGCTLD - previously studied and working; receives tcp/ip commands from GPREDIT to do doppler shift adjustments of sBitx or Icom radio Today: ROTCTLD -- figured out how to run this on a windows machine. Receives trig output of GPREDICT. Converts (in this case) to Yaesu type rotator commands for Az/ elevation and sends out serial port (in my case, COM4, 9600 baud) K3NG Rotator Controller -- I havent made a board for this yet. So I took one of my homebrew WINKEYER ARDUINO simulators, and reprogrammed it using K3NG code to "act like" the controller, handling Az, El controls, reading the CW speed control as if it were an azimuth potentiometer; running the display and activating the "key" and "PTT" to rotate clockwise or counterclockwise. The reprogramming of my Winkeyer Arduino appeard to be a huge success. I properly set the pins to run the display, which worked FINE. It was reading the speed pot as an azimuth reading, and if I pushed "buttons" it would read different elevations. ROTCLD happily connected to it at 9600 baud, and the "rotator controller" accepted commands and displayed them. I was not able on the first test to monitor whether it activated simulated motor controls (key output, etc) -- but that will come. So huge success here and soon (days, weeks?) I should be able to lay out a board (many others have done so before me, but some just did crazy wiring between variuous "shields") to put all this in a neat little package with relay outputs, possibly with PWM output (dunno)., to control available rotators for real. 73 Gordon KX4Z

Even if you did not know who Mike was, you know his work. Mike was a key developer of hamlib in addition to many, many other contributions to our hobby. I only had the privilege of a few email exchanges with him but you would be hard pressed to find a kinder, more helpful ham anywhere. https://dukerandhaugh.com/obituaries/michael-d-black/

1). Wsjt-x only receives data if the Zbitx display is active on my monitor. 2). Cannot manually start rigctl if I shutdown the zbitx display. Rigctl returns network connection error. 3). With the zbitx display window open and wsjt-x running and the mode set to digital, I cannot use the zbitx display to change bands. Band change only works if it is done via wsjt-x 4). When changing bands on wsjtx the zbitx display shows the correct band reflecting the change but wsjtx does not. 5). Receive works fine BUT cannot transmit/tune from wsjtx. I can transmit and tune from the zbitx display window but not from wsjt-x. NEED HELP with number (5) and clarification with what is going on with rigctl. I'd like to be able to start rigctl from CQRLOG and then run WSJT-X without having the zbitx display active if that is possible Thanks, Leo AI5II

Just Curious if the zBitX has any SWR monitoring or display? Regards, Everett-WB9FUW