¿ªÔÆÌåÓý

The upgrades were shipped last Friday, I am told.

Barry, The 1K resistor at the input of the RX mixer provides the correct termination for the bandpass filter. The bandpass filter is terminated with 1K on the mixer side and 50 ohms on the other side.

Group, I believe there is an error in the schematic of the daylight again radio. The RX first mixer has the PTO going to the gate with the high impedance input, while the RF input is going to the gate

Thanks, Allen! I just finished working a trial for the physics test tomorrow. Will have to compare my answers to the students to see if I got it right!! I think I bit off a little too much this

Gordon, I want to thank you for all you do for Amateur Radio. You are a busy man and I hope you continue to be. I always appreciate your insights and inputs. Keep it up! 73 Allen Hill KI4QCK

This was a project from a good bit ago, (April 2021) but here¡¯s the link to the shared project on . Pcbway.con https://www.pcbway.com/project/shareproject/13_8VDC_Polarity_Protector.html I checked

Chuck, What happens when you select the straight key in the configuration, select CW,? and use the mic PTT to key CW? 73 Evan AC9TU

I am not really worried because the buck converter is about 5€ and one irf24 from Infineon is about 0.5€ If I buy from a standard distributor in Germany, so postage for Ashar is probably more

JIm,I agree with your points and also agree with Gordons, too. I would suggest if you can buy them for $5 from china, thats pretty cheap on the price. And if you can bundle them into a nice price, you

I know this is a year late, but i would continue to build it,stockpile it and either take it over to india,and other countries that would appreciate the medical equipment to save lives 73 David ac9xh

Evan I have Two ubitxs and I loaded one with N8ME and one with N8ME with VU3GAO mods and I am getting the same. No side Tone for CW. I sure the CW is Selected I sent used key and my watt /swr meter is

*Hi? Evan,? just compiled and uploaded? the vu3gao mods? firmware, and i? get the same result.. seems to be working ok*

I am worried too, I have sBITX s/n #0052 but haven't received an upgrade kit for it yet. -- Stephen, KO4CVU

Dear self-described grumpy old man! What a hoot! I think you missed a few details? I don¡¯t make these boards at all. I don¡¯t sell them either - so maybe that¡¯s why I don¡¯t advertise a price???

Gordon, I clicked through all the stuff to see about getting a PCB for the reverse voltage protection device. After a few pages, I was disappointed to see an asking price of USD$28 and change.

*THOUGHT SOMETHING WAS UP,? THANKS EVAN*

Art, You do not have the correct software.? Go to this file and download it: /g/BITX20/files/uBITX_6_N8ME_2_VU3GAO_Mods.zip Then follow the instructions on Farhan's video to compile

It is concerning. If they really were shipped out by USPS last week, some people should be getting them by now, and others would have gotten the upcoming delivery notice if they're signed up for

Still looking for the files for the toroids if they're available.? If not, I'll take a shot at making them myself. 73, Dean KK4DAS

*TKS Howard, have just loaded N8ME firmware ver 0.1.. * *Have? boot screen which shows 3 lines of data, * 1 = band - splt - 200 - finp - rf att 2 = usb? ?- rit? ? - tune - cfg - cw spd 3 = m1 -