开云体育

Sorry... www.hamskey.com

The CEC firmware types are located at www.hamskey.net ( http://www.hamskey.net ) which describes what each version can do. I would suggest firmware at 1.0 or higher, 1.2 is the current release. 73

Ted, sorry it took so long...but, I have your 3.5" tft. I have pretty much everything mapped out. Smeter, cwdecode, and spectrum are all in the proper places. I used the hmi file you sent me.

All: Al has made the Gerber files for his RA8875 display protection board available to all who might be interested. The Gerber files and a documentation file are in the attached zip file. I will also

No worries! Its all part of the learning process for all of us :) And nothing astray, it's really hard to articulate exactly ones intentions over text, But we have been making progress in some form or

Hello Curt and Ron... i have performed this mod on my v5 and my resistors were 2.18 k and 10.00 k for dit and dah respectively.? If on the off chance you are using a front panel board from

Ron the schematic here conveys what is going on -- https://ubitx.net/wiring-up-a-paddle-and-straight-key/ note that the 4.7k resistor provides straight key action, then note the 2 added resistors

This is good to know. What I will likely do for now is to stick with the nano and a 1620 display for now since I know that will work and once I get enough experience with arduino in general I might

Hi As Jack says the Si5351 module is Ok but I think you could find one at a better price.? However be very careful with the display this is a line from the advert 8 bit digital interface,plus 4

I have the same V.4 high-pitch oscillation problem and have had no luck addressing the problem. I have done the following: 1) Rewired all audio pathways with grounded RG174. 2) I added an

Tim, do you have any other "commercial" rig with an s-meter? I'd be curious to know what your voltage measurements of 0.3V to 2V might read on another rigs s-meter.

Tim, I read your post on a phone and didn't properly see that you were asking for the sig generator at 7.101, so I got it backwards.. My eyes have been getting kinda messy later in the day. The

I have v3 board with .20 firmware. The keyer on the dot side acts like a straight key. The dash side works fine. The resistors are installed. I tried loading another firmware and it gave me dark

Sold quickly. Thanks. Jim, N5IB

I literally did the preformed text groups.io please stop stripping it. ``` 7.101mhz on the Signal generator USB mode on the ubitx UBitx dial frequency on 7.100 ``` -- Tim Keller -

Let me start with my number I don't have fancy tabulated data but spinning around the bands i get anywhere from like .03 up to 2v when the local 100w station fires up. No signal generator to make

Thanks Tim, Digger and David. Your support is much appreciated especially from Kit-Projects. Digger,I am using a miniature MIL Spec rotary switch for the Kit-Projects AGC board. No problems

I'm sure the parts are okay, and I've used the Si5351 board and it works fine. I don't know about the display, especially if you plan on using the touch screen feature. The Raduino uses a Nano and I

Hi: I would like to give home to this rig. PayPal is ready my address is a USA address. Miguel WP4ZI On Sun, Apr 28, 2019 at 9:11, n5ib_2<n5ib@...> wrote: Selling my uBITX v3, fully assembled

Jack are these ok?? https://www.ebay.com/itm/CJMCU-5351-Si5351A-Si5351-I2C-clock-generator-breakout-board-signal-generator-FY/123733730114?(