开云体育

I think that I had a similar problem to what has been described. Someone suggested that I check to make sure that I wasn't using a monaural plug for the speaker. Yikes!! That was the problem! You

Some of you have missed my point. I do not care if the Raduino is not the same as between BITX40 or uBITX. I have plans on using uBITX without the Raduino it comes with. Why pay for something I'm

even the broken resistor could slowly be salvaged by using a thin wire instead of original wire. it would be possible However one side resistor woronal wire would hold it in position. finally even

http://ubitx.net/ _._

Really? Buy one of these: Arduino Nano V3.0 I/O Expansion Board NANO I/O Shield For Arduino NANO IO | eBay | | | | $ 1.34 | | | | | | | Arduino Nano V3.0 I/O Expansion Board

Ashhar:? We need a breakout just for uBITX.? Searching through BITX20 and BITX40 to find things on uBITX is a pain.? Please: can you do something about this?

I dont have a 4.7k? but I do have a 5.1K? I wonder if that is close enough?? But it is a carbon resistor. What do you folk think?? maybe shoudl be patient and order the exact replacement. -- 73,

Glad you mentioned this.? I am in the process of wiring my ubitx up and sure enough this and the volume controls were wired per the diagram and wrong. I rewiring the lead on the resister broke off

All my Encoder playing around has been on BitX and with interrupts.? Using Encoder library. Maybe you could experiment by making a sketch by stripping out from uBit code that just includes reading

Hi Sarma, I tried both .1 and .01 on 3 different Raduino installations. It doesn't make a noticeable difference on my 3 anyway. I'll put the .01's in anyway just in case. Jim

I have pinned it down to the Asus router itself.? If I connect my PC directly to the Comcast modem, it works just fine.? So it's time to replace that router (I have a replacement sitting here

I tend to go with hardware to debounce mechanical contacts.? There are some elegant solutions from Paladin Semiconductor: Pushbuttons ( http://www.paladinsemi.com/pushbutton_interface.php ) They

Just for giggles, change your network card's DNS to 8.8.8.8 (that's Google's public DNS) and try it. Comcast may not have had their DNS refreshed or their DNS might have rejected it for some odd

What ever be the internal circuitry, the pin out would not change, I suppose. Regards MVS Sarma

The problem turns out to be with my Comcast modem, apparently. The problem is that I can not connect to through Comcast - not an email problem.? The email is working fine.? If I

Not completely sure but I think it will work OK. The only difference is that the coil resistance is slightly higher but I believe this is not critical for use in BitX. Why not just try it out? 73

Hi! Do you think this may work??https://www.ebay.es/itm/ZETTLER-AZ822-2C-12DSE-Relais-12V-DC-2xEIN-2A-960R-DIP-Relay-Sensitive-855056/361891187328?hash=item5442654a80:g:UBsAAOSwMmBV4C5C I see the

Modified TPA Libraries:?/g/BITX20/files/TPA2016%20Library

TDA2822 does not have to warm up if it does is defective or it oscillates! But the amplification is too high to the needs, try to use agc on the audio or decrease the IC gain!

Hi mike, I'll put the files up soon... I did have the same issue with low audio. That is what the noise gate threshold is for, we want to set it very low(0) so that it lets even weak signals and