开云体育

This code expects the I2C bus to be kernel I2C interface. Make sure you have one of the dtoverlays in /boot/firmware/config.txt For loading the I2C Bit-Banged (BB) driver in the appropriate sBitx

Thanks Jerry. I will test it and see if the issue goes away. I think this is just more garbage code that wasn't removed from the file for earlier versions of sBitx hardware. That is the unfortunate

They’re the same. 73 de ai4ot Get Outlook for iOS<https://aka.ms/o0ukef> ________________________________ Sent: Friday, March 22, 2024 12:17:17 PM To: [email protected] <[email protected]> Subject:

Many thanks Evan. Art Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows ________________________________ Sent: Friday, March 22, 2024 1:08:20 PM To: [email protected]

in sbitx_gtk,c is the function, time_t time_sbitx(){ if (time_delta) return (millis()/1000l) + time_delta; else return time(NULL); } If you just return(NULL);

Thanks, I just found you video on it and saw the separate board.? ?Can I put a longer cable on the board?

EUREKA!!! I was able to reproduce the problem.. After I entered a different gridsquare, the time is now off by an hour. I think there is a bug in the sBitx software.. I can now troubleshoot this

Thank you Pete and Gyula. I feel bad that there are still issues with it and am frustrated about it. I want to give you a better experience than you received from HF Signals. I will continue to work

Hello N4GW, The two encoders are on a separate board as described on the HFSignals page: https://www.hfsignals.com/index.php/sbitx-v3/ Buy a fully tested sBitx-v3 board with the heatsink mounted.

They are on a separate board connected with a supplied FRC cable to the main board. [email protected]> wrote:

Hi, I was thinking about getting the V3 board.? I want to use it with an 11 inch display, so was curious about how the multi knob and VFO were attached.? Are they on a separate board.? If they are

Hi Elmers, I have a nicely built Hendricks Bitx20 v1.3 I bought at a hamfest. The power plug out (female) is the wrong size to my power supply battery pack, male plug. I have a Rockmite, that has

Has anyone used the 3D printed case from Thingiverse?

The issue isn't with the shaft lengths of the encoders. the problem is that they use the threaded body of the encoder to mount the board to the case. unfortunately, the height of the connector against

Hello Art, You are correct. If you have an editable version, you can change the numbers to match the manufacturer's numbering on the schematic. 73 Evan AC9TU

Hello Evan, nice to hear from you again.. Yes the schematic showing relay K1, (2019) in my case is using pins which are completely opposite in physical placement according to the manufacturer’s

After entering " \utc 2023 05 01 05:00:00" into the command box, it did change the date/time in the title bar, but no change after a restart, and I2C is enabled. Thanks for what you have done so far

Postscript: which got a bit long. All the modifications I made to myself were because I wanted to use the device. So in mid-November, when the v3.0 alpha was released, I built an inclined vertical

Hi Art, All of the relays are the same.? The difference is in which corner pin is called pin one.? The schematic has been updated from the original v3 to fix filter layout issues that resulted in

When I typed my previous message, I did before I typed in SBITX A /UTC 2024 03 21 Some time, but no change. I think the funds have to look for the cause. I remember when the de de appeared, the RTC