开云体育

Hyderabox! uBITX in a Lunch Box | | | | | | | | | | | Hyderabox! uBITX in a Lunch Box Radio electronics blog. Homebrew ham radio. SolderSmoke podcast. QRP | | |

Should be possible using Winlink Express. Your position is input manually or via a GPS device. This is then displayed on the Winlink clients Google map. Bernie KC9SGV

Hi Tim I was getting 25 watts on my watt meter. om 80m. Today hooked up a 10m dipole and got 2.5watts with keyer down. With a low swr.? Delta Alpha Victor Echo

Hello Ad, Yes there is. It is in the older folder below. The file is called ATU Schematics and pictures. ? It is a servo based ATU, not a relay based one. It works nicely, a little slower than a

Hi SaMa, First you must install the PinChangeInterrupt library in your IDE (the Arduino/Genuino software). The PinChangeInterrupt library is normally not installed by default. You have to add it to

Is there a schematic somewhere for this extra arduino / atu? Would love to build it. -- Ad, PE1GIJ

Hello I am wondering if anyone know how to: - enable FSK/RTTY interface to the radio? - ptt out for amplifier?? Best Regards, Stein-Roar Brobakken post@... LB3RE K3RAG Skype: lb3re.rag

Hello Thanks! I order :) --- Best Regards Stein-Roar Brobakken Den 2018-04-21 09:12, skrev Joe Puma:

I have uploaded an update of both the Raduino and the ATU software in the folder??Variations on KD8CEC Software (by VK2ETA) + ATU sketch?. (

Good morning I was advised to upgrade to the Allard's version https://github.com/amunters/bitx40 that solves many problems! I downloaded the zip and unzipped it then I installed the Arduino/Genuino

I would go with the rtl-SDR.com v3 dongle. I use it with my Yaesu FT-840. And I have about 4 others that make up my radio farm. To me it’s the best design of the dongle type SDR’s no need to get

Hello Anyone have a suggestion for a rtl sdr device for use with uBitX? Best Regards, Stein-Roar Brobakken post@... LB3RE K3RAG Skype: lb3re.rag

Hello Resti, It depends what you mean by "via bitx". If you mean without the addition of an external device, I don't know of such a solution, but it may have been done by someone. It is technically

Hello everyone, can we send gps data via bitx? thank you

Thank you. These links look good. Regards. Max K 4 O D S. I've Never Lost the Wonder. Antique Electronics Site: <http://www.angelfire.com/electronic/funwithtubes/>

My mic is ugliest of all. Regards. Max K 4 O D S. I've Never Lost the Wonder. Antique Electronics Site: <http://www.angelfire.com/electronic/funwithtubes/>

And the volume control ground is green. Sent: Friday, April 20, 2018 8:52 PM To: BITX20 Subject: Re: [BITX20] uBITX wiring question The grounds for the arduino are located on several pins -

Not all ground wires are black and not all black wires are ground. The mic ground is blue and the ground for keyer and encoder is yellow. The encoder A connection is black. Mike K5ESS Sent:

The grounds for the arduino are located on several pins - marked gnd The rig grounds are the black wires but i test them to be sure. I keep my grounds short and tie them to the chassis. Either

Hi, Sorry if this has been addressed, but I have a question regarding the grounds on this board. Are the grounds for the Raduino (terminal 4) and the audio grounds considered common grounds? And can