开云体育

Thank you Vince, tried it but failed: We could not find this Tracking Number in our system. You can edit this Tracking Number or Request Delivery Updates By Email . 73! George VE7WQ Friday,

Here's the final version with ventilation.? ?To remove and reverse the bottom panel I drilled out the punches with a 7/32 bit, and then enlarged the outer holes with a 1/4 bit, so 1/4" screws hold

*Voyage of a **μ**bitx from India to Malta.* *Ordered 10 December 2017* https://www.aftership.com/couriers/india-post-int *Feb 15, 2018** 07:10 pm* *Send item to domestic location (Inb)India Post

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the BITX20@groups.io group. *File:* ubitx_V2_01R.zip *Uploaded By:* Jim

The CW Keyer module has been completely re-written in this version.? The keyer is now totally interrupt driven which helps make the transition to CW transmit much faster and it doesn't tend to clip

Try going to your postal site (Canada Post?) and use their tracking. I know packages from other countries destined for the US can be tracked at USPS.com. Vince. -- Michigan VHF Corp.

My 2?: I can buy the B40 w/Raduino for $59.? I'd consider $40-50 shipped a fair price, but interest is a lot less with advent of the ?B. The frequency counter and other displays are redundant

The BITX40 ordered on Feb 16 was shipped today via India Post. Got a tracking number, but no url where I can check it. 73! George VE7WQ Saturday, February 10, 2018, you wrote: VV> utilize the rest

Ryan: See if the attached encoder article is of any help. It should at least get you started playing around with the encoder. Jack, W8TEE To: BITX20@groups.io Sent: Friday, February 16, 2018

Mike, Mesure the voltage across the resistors and you know the resistors value. Calculate :if I remember right V2/R = Voltage squared divided by resistance to get the power dissipated. That should

It's probably worth mentioning that the "free" A1 refers to the original BITX40 code. Line 146 in that code shows: // #define ANALOG_KEYER (A1) which is commented out. If you do use that pin for the

Thanks for the responses so far, but what I REALLY want to know is if $100 is too high or too low to expect for all this stuff?

The other board was a VK3YE that he said did not work very well. -Fred KC3HMS <michael_r_monteith@...> wrote:

I have just finished chasing the smoking R141. Even after replacing the smd with an axial 1/2 watt, mounted vertically, it continued to get blazing hot after only 2-3 seconds of PTT. Be sure to check

Some more info and pictures for anyone wanting to use the uBitx on 160m. I’m having a blast on 160m I did add larger heat sinks and a pair of small fans that I can turn on and off as needed to

Steve, you need to install?the TX-RX mod so that the radio will go into TX when you press the button. Alternatively, you can press PTT manually on the mic and then press the tune button. 73 Allard

Thanks Mike, but according to this ( https://github.com/amunters/bitx40/blob/master/operating-instructions.md ) ,? ------------------------------------------------- CONNECTING A STRAIGHT MORSE KEY

Tune button? There is no tune button with Allard’s mods! Maybe you are thinking of the CW spot / fine tune button? This puts a tone on cw for allowing you to align the incoming signal with the

Hello All, I got Allard's Raduino sketch to compile on an Uno R3 that I'm playing with, and I also got a rotary encoder working on a test sketch, and now I need to figure out how to make Allard's

Hi gang.? I've got my '40 assembled, tested, and mounted in a box.? Loaded Allard's latest as well as all his hardware mods, with the exception of the TX-RX mod.? 6W output on SSB, but no output on