If 12V, maybe go to
3.3 to 4.7K.? Leds are fairly bright at a couple of ma?
Mike
On 11/5/2017 2:33 PM, Dexter N Muir
wrote:
Mike beat me to
it, and with better. Resistor first, then wire to diode/s (raw
voltage to flying leads not the best idea! :)
73!
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
Mike beat me to it, and with better. Resistor first, then wire to diode/s (raw voltage to flying leads not the best idea! :)
73!
|
Easy, Ben! Consult the circuit diagram. Relay K1 is supplied with +12V. It then feeds either +RX or +TX as the case may be. The underside of the board has the pads to connect to, either to individual LEDs with series resistors to 0V or to a 'bi-color' LED with resistor from its common lead to 0V. Those voltages can be accessed on the top side of the board by locating resistors in the 'bi-amp' section/s and carefully attaching your wires. The traces there follow the circuit diagram. A little mental effort, but well worth it. I'd suggest only a TX LED - if not lit, the rig is is Rx mode. If your kit is non-Raduino, I'd suggest a 'Power on' rather than 'Rx' LED.
73
Dex, ZL2DEX
|
Re: raduino v1.27 released (improved suppression of spurious burst)
Hi, just a quick question about the frequency range, i installed ver 1.26, all ok, then changed the upper and lower frequency range to 3mhz and 15.5mhz. I had hoped to be able to rx 30 and 20 metres using different bpf, but when going up in frequency, the vfo only gets to 9.999mhz then goes back to 1mhz? I cannot get it to go any higher. Cheers John de VK4JWT?
Sent from my SAMSUNG Galaxy S7 edge on the Telstra Mobile Network
|
Just go to the Rx and
Tx lines that control the direction of the amps.? Put a 1K to
each Led from them.
I think that is what
you asked?
73's
Mike, WA6ISP
On 11/5/2017 1:20 PM, Ben Piecora
wrote:
Hi Everyone,
Could anybody tell me a way I can pull voltage
from the board for an LED on RX and then pull voltage from the
board for a TX LED and turn off the RX LED?
Thanks
Ben
KD2NOU
--
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
Hi Everyone,
Could anybody tell me a way I can pull voltage from the board for an LED on RX and then pull voltage from the board for a TX LED and turn off the RX LED?
Thanks Ben KD2NOU --
|
Probably these?
#include "si5351.h"
#include <Rotary.h>
Remember the complaint
the external SI library eats memory?
That's why it is
internal on newer versions.
Mike, WA6ISP
On 11/5/2017 1:00 PM, Henning Weddig
via Groups.Io wrote:
yes, now it compiles:
"Build-Optionen wurden ver?ndert, alles wird neu kompiliert
Der Sketch verwendet 15464 Bytes (50%) des
Programmspeicherplatzes. Das Maximum sind 30720 Bytes.
Globale Variablen verwenden 838 Bytes (40%) des dynamischen
Speichers, 1210 Bytes f¨¹r lokale Variablen verbleiben. Das
Maximum sind 2048 Bytes."
but I am wondering why this sketch uses abouzt 50% of the
available programm memory space !
Henning
Am 05.11.2017 um 21:54 schrieb
Michael Hagen:
OK, comment out
LCD.H
and
// LCD Backlight
ON
//lcd.setBacklightPin(BACKLIGHT_PIN,POSITIVE);
//lcd.setBacklight(HIGH);
Now it compiles
here?
Look like those
functions are in some other library other than the
standard Liquid Crystal library?
?
WA6ISP, Mike
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
yes, now it compiles:
"Build-Optionen wurden ver?ndert, alles wird neu kompiliert
Der Sketch verwendet 15464 Bytes (50%) des
Programmspeicherplatzes. Das Maximum sind 30720 Bytes.
Globale Variablen verwenden 838 Bytes (40%) des dynamischen
Speichers, 1210 Bytes f¨¹r lokale Variablen verbleiben. Das Maximum
sind 2048 Bytes."
but I am wondering why this sketch uses abouzt 50% of the
available programm memory space !
Henning
Am 05.11.2017 um 21:54 schrieb Michael
Hagen:
toggle quoted message
Show quoted text
OK, comment out
LCD.H
and
// LCD Backlight ON
//lcd.setBacklightPin(BACKLIGHT_PIN,POSITIVE);
//lcd.setBacklight(HIGH);
Now it compiles
here?
Look like those
functions are in some other library other than the standard
Liquid Crystal library?
?
WA6ISP, Mike
|
OK, comment out LCD.H
and
// LCD Backlight ON
//lcd.setBacklightPin(BACKLIGHT_PIN,POSITIVE);
//lcd.setBacklight(HIGH);
Now it compiles here?
Look like those
functions are in some other library other than the standard
Liquid Crystal library?
?
WA6ISP, Mike
On 11/5/2017 12:39 PM, Michael Hagen
wrote:
Here are the libraries installed?? There are 2 screen dumps
shown.
LCD.h has to be somewhere?
Maybe addons from Adafruit?
Mike, WA6ISP
On 11/5/2017 12:20 PM, Michael Hagen
wrote:
Yes, does not
compile here if I comment out LCD.h.
I am trying to
find LCD.h.
??? Have not found
it yet?
?
Mike
On 11/5/2017 12:06 PM, Michael
Hagen wrote:
This just compiled
here?
Mike, WA6ISP
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
Here are the libraries installed?? There are 2 screen dumps
shown.
LCD.h has to be somewhere?
Maybe addons from Adafruit?
Mike, WA6ISP
On 11/5/2017 12:20 PM, Michael Hagen
wrote:
Yes, does not
compile here if I comment out LCD.h.
I am trying to find
LCD.h.
??? Have not found
it yet?
?
Mike
On 11/5/2017 12:06 PM, Michael Hagen
wrote:
This just compiled
here?
Mike, WA6ISP
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
Yes, does not compile
here if I comment out LCD.h.
I am trying to find
LCD.h.
??? Have not found it
yet?
?
Mike
On 11/5/2017 12:06 PM, Michael Hagen
wrote:
This
just compiled here?
Mike, WA6ISP
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
Thanks Mike
I will give it a try. Also, I hate auto correct on this tablet. It makes me look illiterate!
|
This just compiled here?
Mike, WA6ISP
|
It should be the
standard LCD Lib, but need the SI5351 and Rotary.
I will try it, and
email again the file.
Mike
On 11/5/2017 11:48 AM, Henning Weddig
via Groups.Io wrote:
I tried to compile, but get this error:
Build-Optionen wurden ver?ndert, alles wird neu kompiliert
D:\BITX_40\WA6isp\RFGen5351V3\RFGen5351V3.ino:55:17: fatal
error: LCD.h: No such file or directory
?#include "LCD.h"
???????????????? ^
compilation terminated.
exit status 1
Fehler beim Kompilieren f¨¹r das Board Arduino Nano.
So the lcd.h file is missing! Where can I find it?
Henning
DK5LV
Am 05.11.2017 um 20:15 schrieb
Michael Hagen:
I have hacked up a
generator.
I hope this is the
latest?
Uses Raduino or
RaduinoX and Rotery Encoder.
See if it works?
Mike, WA6ISP
On 11/5/2017 9:21 AM, Brent Seres
wrote:
Hi all
I now have a spare radio which I would like to use to put
together a little signal generator. No point in regards
inventing the wheel if anyone already has a simple sketch I
could use. I have Mike's excellent upgrade, so was going to
use the original radio for this.
Thanks
Brent
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
I tried to compile, but get this error:
Build-Optionen wurden ver?ndert, alles wird neu kompiliert
D:\BITX_40\WA6isp\RFGen5351V3\RFGen5351V3.ino:55:17: fatal error:
LCD.h: No such file or directory
?#include "LCD.h"
???????????????? ^
compilation terminated.
exit status 1
Fehler beim Kompilieren f¨¹r das Board Arduino Nano.
So the lcd.h file is missing! Where can I find it?
Henning
DK5LV
Am 05.11.2017 um 20:15 schrieb Michael
Hagen:
toggle quoted message
Show quoted text
I have hacked up a
generator.
I hope this is the
latest?
Uses Raduino or
RaduinoX and Rotery Encoder.
See if it works?
Mike, WA6ISP
On 11/5/2017 9:21 AM, Brent Seres
wrote:
Hi all
I now have a spare radio which I would like to use to put
together a little signal generator. No point in regards
inventing the wheel if anyone already has a simple sketch I
could use. I have Mike's excellent upgrade, so was going to use
the original radio for this.
Thanks
Brent
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
I have hacked up a
generator.
I hope this is the latest?
Uses Raduino or
RaduinoX and Rotery Encoder.
See if it works?
Mike, WA6ISP
On 11/5/2017 9:21 AM, Brent Seres
wrote:
Hi all
I now have a spare radio which I would like to use to put together
a little signal generator. No point in regards inventing the wheel
if anyone already has a simple sketch I could use. I have Mike's
excellent upgrade, so was going to use the original radio for
this.
Thanks
Brent
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
|
Hi all
I now have a spare radio which I would like to use to put together a little signal generator. No point in regards inventing the wheel if anyone already has a simple sketch I could use. I have Mike's excellent upgrade, so was going to use the original radio for this.
Thanks
Brent
|
Try Ebay number:? ?? 201853209420201853209420 eBay item number: 201853209420
On Sun, Nov 5, 2017 at 6:57 AM, G1WDF <wobblyandflo@...> wrote: I've had an hour browsing the old posts looking for a source for a trim panel to go around the standard bitx40v3 display.
No luck finding anything. Does anyone have source for such an item? They seem to available from photos in the photos section.
A UK source would be ideal.
Cheers, Richard.
|
Re: BITX QSO Night, Sunday, November 5, 7pm Local Time, 7277 kHz in North America, 7177 kHz elsewhere
Tom, this is a regular Sunday evening event.?
--
John - WA2FZW
|
Re: BITX QSO Night, Sunday, November 5, 7pm Local Time, 7277 kHz in North America, 7177 kHz elsewhere
I hope there will be others or maybe a regular thing, as I have not put my bits together yet.?
|
radiomanjwt
Brent Seres/ VE3CUS