Ruarto
Recognize that much of the assembly is soldering wires. First take some time having fun to identify the version, and how it goes together. The ubitx has a prominent set of 4 relays, compare pictures. Perhaps examing the parts may convey that you can assemble it. Maybe you can work with a local ham if you later need to. Its an opportunity to enjoy radio, one step at a time.
Curt
|
? I have been lurking and trying to follow these treads and am getting real nervous.? ? I am elderly and not that proficient of a electronic tech,? don¡¯t have oscilloscopes, etc.??? I was told it was ready to work just needed to be assembled.???? Was I wrong? ? Am I in trouble here? ? I have about everything,? case, board, etc¡.???? but now am wondering if I should perhaps get someone younger (less shakey) and with more electronic and radio savvy to assemble it for me for a fee. ? ? I got this a couple months ago,? and think its possibly a bitx40 not a 20.?? Or basic ubitx.?? ? Any suggestions?? ? ? ? ?
|
This tells me that there is a fault BEFORE the first mixer. High probability is a shorted
trifilar transformer. I found one such case by rocking the toroid and there was a jump
in SSB power.
Check the 45MHz L5 and L7 for bad connection. You can check for continuity with a
multimeter.
Most probably the fault is somewhere common to RX and RX.
Good luck, faults are usually very simple.
Raj
toggle quoted message
Show quoted text
At 27-10-18, Evan Clark (OSC) wrote: Thanks for the help everyone. I am now seeing over ten watts out when keying CW. Still need to fiddle with the SSB as I have no power out there. I also have some issues with the audio, I think that's just due to incorrect tune up but it seems way off. Thanks for everyone's help!
|
Re: QSX 10W HF Linear PA kit
I use one that came with a Dremel. Small and handy.
I found the holes for the 0.6mm wire to be a tight fit. After making
bifilar
transformer the lead wires will not be straight and they struggle to
get through the kit pcb holes.
Hans can keep this in mind!
Half kit done, rest later!
Raj
At 26-10-18, you wrote:
toggle quoted message
Show quoted text
On Thu, Oct 25, 2018 at 11:21
PM, Glenn wrote:
another small issue..... all holes in the heat-sink have burs on
them.
You want to keep it FLAT as the devices have to be flat to it for best
heat transfer.
Burs are easily removed with a precision knife (Exacto or similar).?
A good builder
checks for accidental shorts prior to power up.
FYI the bigger thing is that the FBxx-2402 ferrite have sharp edges on
the holes
and can strip enamel from wires while winding.? I use a small cone
shaped
Carborundum stone to take the edges of the holes down.
Allison
|
I hope you are not trying it with the K3 on the same bench.? You will fully overload (even the K3). it will give you wrong readings. - f
On Sat, Oct 27, 2018 at 2:26 AM Timothy Fidler < engstr@...> wrote: Forgot word to the wise? - TEF for what it is worth strongly advises against making Allard hardware mods with Original Farhan software/firmware in place. Or? ?you may go to hell in a hand basket with all sorts of issues? and? people like Maestro? Allard may have trouble working out where the hell you are. I Suggest you try to get out of current hole before you try to reflash the nano uP (if that is what you might think of next) .? People have been down that route and ended up with no tcvr at all (you really need a second Raduino to be sure you have a backout path).. ..or live dangerously.
|
Ah, good to hear!
Jerry
toggle quoted message
Show quoted text
On Fri, Oct 26, 2018 at 04:29 PM, Evan Clark (OSC) wrote:
Thanks for the help everyone. I am now seeing over ten watts out when keying CW. Still need to fiddle with the SSB as I have no power out there. I also have some issues with the audio, I think that's just due to incorrect tune up but it seems way off. Thanks for everyone's help!
|
Re: PA Alignment of uBITX
#ubitx
John
The key here is the 100 mA delta, per stage.
The receive current varies between minimum volume with no signal, and higher volume with a strong signal.
I sense you accomplished it okay.
Curt
|
I'm not so concerned about the actual freqs but I would have thought that CLK2 would be the same freq on either USB or LSB for a given dial freq? but that doesn't seem to be the case. I'm trying to understand why that is. And what it should be.
And a small correction...I'm running CEC V1.11, not 1.01.
|
Re: QSX 10W HF Linear PA kit
Hi, My package arrived from QRP Labs today. I was surprising how small these kits are. I thought they had only sent the amplifier until I looked much closer at the contents through the bubble wrap. QRP Labs seems to be well thought of so I believe these kits, I'm especially interested in the PA, will provide good design baselines for amplifier and filter projects. Tom, wb6b  --------  ?
|
Re: QSX 10W HF Linear PA kit
Allison,
I bring the points up, so others less skilled then yourself or other experienced builders, can be aware of them when building the Amp, as they are not mentioned in the instructions.
I¡¯m not doubting the value of the Kit, I think it¡¯s excellent.
Glenn
|
Thanks for the help everyone. I am now seeing over ten watts out when keying CW. Still need to fiddle with the SSB as I have no power out there. I also have some issues with the audio, I think that's just due to incorrect tune up but it seems way off. Thanks for everyone's help!
|
¡°¡±Command an output freq equal to the stated crystal freq¡±¡±
Was what it was supposed to say. Sorry, missed that Siri error...
toggle quoted message
Show quoted text
On Oct 26, 2018, at 19:16, Gordon Gibby <ggibby@...> wrote:
I don¡¯t know, but the easiest way is simply to come in and output equal to the stated Krystal frequency and then adjust the crystal freq constant in the software to actual value . Mine typically were off by three or 4 kHz.
Correct the crystal frequency Constant in the software appropriately to represent reality, and then every frequency they create becomes perfect.
On Oct 26, 2018, at 19:03, Mark M <junquemaile@...> wrote:
As part of my endeavor to calibrate my uBitX V3 running the CEC 1.01 firmware, I was measuring the raduino clock frequencies with my frequency counter. My thought was to tweak the master clock via the Configuration Manager so that CLK2 is exactly 55 MHz when tuned to 10 Mhz. I was able to do that with USB selected but when I switched to LSB I was surprised to see CLK2 drop by about 6 kHz. I thought that CLK2 would be the dial freq plus 45 regardless of which sideband was selected, and that USB/LSB was determined by CLK1.
Clocks 0 and 1 appear to behave as expected.
What am I not understanding here?
Mark AA7TA
|
I don¡¯t know, but the easiest way is simply to come in and output equal to the stated Krystal frequency and then adjust the crystal freq constant in the software to actual value . Mine typically were off by three or 4 kHz.
Correct the crystal frequency Constant in the software appropriately to represent reality, and then every frequency they create becomes perfect.
toggle quoted message
Show quoted text
On Oct 26, 2018, at 19:03, Mark M <junquemaile@...> wrote:
As part of my endeavor to calibrate my uBitX V3 running the CEC 1.01 firmware, I was measuring the raduino clock frequencies with my frequency counter. My thought was to tweak the master clock via the Configuration Manager so that CLK2 is exactly 55 MHz when tuned to 10 Mhz. I was able to do that with USB selected but when I switched to LSB I was surprised to see CLK2 drop by about 6 kHz. I thought that CLK2 would be the dial freq plus 45 regardless of which sideband was selected, and that USB/LSB was determined by CLK1.
Clocks 0 and 1 appear to behave as expected.
What am I not understanding here?
Mark AA7TA
|
As part of my endeavor to calibrate my uBitX V3 running the CEC 1.01 firmware, I was measuring the raduino clock frequencies with my frequency counter. My thought was to tweak the master clock via the Configuration Manager so that CLK2 is exactly 55 MHz when tuned to 10 Mhz. I was able to do that with USB selected but when I switched to LSB I was surprised to see CLK2 drop by about 6 kHz. I thought that CLK2 would be the dial freq plus 45 regardless of which sideband was selected, and that USB/LSB was determined by CLK1.
Clocks 0 and 1 appear to behave as expected.
What am I not understanding here?
Mark AA7TA
|
Forgot word to the wise? - TEF for what it is worth strongly advises against making Allard hardware mods with Original Farhan software/firmware in place. Or? ?you may go to hell in a hand basket with all sorts of issues? and? people like Maestro? Allard may have trouble working out where the hell you are. I Suggest you try to get out of current hole before you try to reflash the nano uP (if that is what you might think of next) .? People have been down that route and ended up with no tcvr at all (you really need a second Raduino to be sure you have a backout path).. ..or live dangerously.
|
MT did you try my suggestion to install the NBR 12 xtal ..the highest of the complete set to try to pull the BFO up and get the USB out of the way ?? IF not , You have a socket , suggest you try it - given .? ?Also have you used the variable capacitor at the BFO to the same end ? Remember too that when you did the change out you now have a set of capacitors that are NOT calculated for you xtal set in the Cohn filter.? It may be fine but it is all in the reason of should be.? Finally to avoid changing out the cheap and nasty L in the BFO set (it looks too small to be of much use (I suspect the intent is to set the BFO wrt filter by xtal selection primarily) - finally you could use the next lower xtal set (that you made up by freq measurement - not shown on this post - ) to install as a pair in //el in your socket? to make up a super Vxo which is much more pullable using the LC set and you can go upp up and away.. up the ladder of success (like Don Draper/Dick Whitman? in the Lift ). MMen ;? Love it.?
|
Re: PA Alignment of uBITX
#ubitx
Thanks Curt, Ok.?
That is step 1 and it feels like now I am putting out some power (rather than previously my dummy load didn't even warm up).
Trying now to understand the BFO setup - I think that is not setup correctly as I just hear "clicking in the audio".
John
|
Allison's right, I screwed up on my last post.
That post was thinking it was a Bitx40, not a uBitx.
Ignore my last post.
Unless somebody else jumps in first, I'll try to rewrite that post
once I have some free time again.
Jerry, KE7ER
On Fri, Oct 26, 2018 at 11:34 AM, ajparent1/KB1GMX wrote:
Is this a bitx40 or a uBitx???? They are very different and I keep seeing references to both!
|
On Fri, Oct 26, 2018 at 10:37 AM, Michael Trager wrote:
Anyone know what the purpose of the blue pot on the Raduino...contrast ?
Yes, contrast.
Distorted in what way, tones and pitch are off or voices only squeeky or bassy?
Elaborate?
Its not a DDS it is a NCO (Numerically Controlled Oscillator, a fancy PLL) and the
normal output is square wave.
if PTT changes frequency you have a wiring error or grounding issue.
|
On Fri, Oct 26, 2018 at 11:22 AM, Jerry Gaffke wrote:
With the PTT switch pressed, measure the following voltages:
? ? TX? ? (should be +12v)
? ? U3 pin 1? ?(should be +5v)? ?Could alternately be measured at RV1 or C150
? ? R150? ? (both sides the same and same as the IRF510 gate, should vary between 0v and 5v as you turn RV1).
All of the voltages above are DC, measured with the black probe on ground a
Is this a bitx40 or a uBitx???? They are very different and I keep seeing references to both!
++++++++++++++++++++++++++++++++++++? uBitx only!++++++++++++++++
for ubitx U2 is the 5V source for get bias.? RV2 and RV3 are the bias adjust for each IRF510.
Note no audio into the mic or use a jumper to connect PTT to ground for SSB TX.
To dial in the bias urn the pots RV2 and 3 down to 0V on the gate (oddly its clockwise!).
Measure the radio current, whatever that is adjust RV2 for 100mA more.? The resulting
current is noted and then adjust RV3 for an additional 100ma.? Total current will be about
350mA give or take depending on the starting number.
With 12V on the drains the gates should be at 3-4V and about the same voltage for each
IRF510.
IF the gates are still at zero volts then you have other issues with burned traces.
That being done RV1 set to about 10 o-clock position (2/3 power) (its also backward)
as max power out is anti-clockwise.? Now you should see some power out.
Allison
|
Raj vu2zap