Good one Tim!
Yup, that crossover is missing a junction dot on the AGC schematic.

Also, looks like Kees' schematic is following Don's lead by not showing
where the RF gain pot should be.

Good to see so many clamoring for the boards.
I assume there is no list.
But put me down for 3 each anyway.

Jerry, KE7ER

On the schematic shouldn't R1,R2, and C2 all be shown as connected on
the schematic?

tim ab0wr

On Mon, 30 Apr 2018 15:43:31 -0700
"Kees T" <windy10605@...> wrote:

OK, here is the status. Attached is the board and schematic info for
the AGC Gain Control circuit ND6T designed and RX/TX Click Eliminator
circuit VA7AT designed .....I believe that is correct. It always pays
to hesitate before pushing the button and it's gone .....and besides
they are still celebrating their Labour Day. I'll order with DHL
shipping and I should have boards in 7-10 days at my door based on
experience.

Ken,

As many as required.

We need to build and test a few when the boards arrive (plenty of volunteers) and then we'll let er' rip. Status will be posted here.
Assuming I can get 100% yield on the shear that's 160 AGC and 320 Click boards initially, more as needed after that. With the DHL shipping I'll have to figure out what the board cost is to me and go from there. You will be surprised, it will be quite low. What drives overall kit prices up is US/DX postage, PayPal fees, and packaging. Quantity is what makes it cheap.

73 Kees K5BCQ?

I have seen the eBay panels and they are great but thought I would try on my own first.

开云体育

开云体育

If available i'd take two of each. Steve kb1chu

Could you put me down for one of each. , please.

Thanks

73 KK4JW / Juerg

My Friend Bill Meara confirmed this is OK.

My primary suggestion would be that you blindly follow Allard's suggestions.
Many have, with great results.

I sat through the 8:17 minute April 1 2016 Steve Ellington video on the myantennas EFHW-8010.
Wow, now I remember why I mostly avoid youtube, maybe 10 seconds worth of? information in all of that.
Anyways,he has the matchbox about 5' up in the air, the wire then goes
straight up to 55 feet and then over, and he was planning to rip out his other antenna to make room?
for a second EFHW-8010 so he could swap patterns.? Which is to say that he likes it.
Oh, and on long 80m CW transmit sessions at 500 Watts he sees his SWR creep up suggesting
the transformer was maybe overheating, not an issue on the other bands.??
And he's very fond of LMR-600 coax.

Maybe Simon could give us an executive summary on his other dozen or so videos,
especially the one that's an hour and a quarter long.?
Did Steve E. ever manage to build something he liked better than the EFHW-8010?
What's a good video to start with for somebody wanting to build one from scratch?
Any tidbits not typically found in other material on EFHW's?

Jerry, KE7ER
?

开云体育

I have the w8yee bitx4 vfo but the document does not say what pins to connect from the ggs to the vfo piins/

Thanks for your answer, Jerry.? We'll follow your suggestions.? 73, Keith AG?H

There is a youtube channel by a ham called Steve Ellington that looks at various aspects of the efhw including construction and the myantennas version. Search "EFHW" and the channel came up in a number of the results.

Regards


Simon VK3ELH?

开云体育

Put me down for one of each, please.

Ron W7HD

10270 W Mars Rd

Tucson, AZ 85743

OK, here is the status. Attached is the board and schematic info for the AGC Gain Control circuit ND6T designed and RX/TX Click Eliminator circuit VA7AT designed .....I believe that is correct. It always pays to hesitate before pushing the button and it's gone .....and besides they are still celebrating their Labour Day. I'll order with DHL shipping and I should have boards in 7-10 days at my door based on experience.? ?

-- 
Ron W7HD - NAQCC#7587 OMISS#9898 KX3#6966 LinuxUser#415320
Editor OVARC newsletter

Case is EF-01, ?panels are on eBay.

If it's like the one from Bangood there are 3d printed plastic panels on Amazon that work great. Case is EF-1 or similar.
Bo W4GHV?