I have been having problems where my keyboard keeps disconnecting , I haven't gone too deep to see what the issue is yet.?
On Wed, Apr 2, 2025 at 2:41?PM Ryan Wesolowski via <cosmo1stgen= [email protected]> wrote: Enable Bluetooth on the desktop turn on your keyboard and tell Bluetooth to scan for devices.? You can then pair from there.? On Linux I usually have a problem where Bluetooth wants to repeatedly disconnect from the device until the first reboot.? After that works fine.?
|
Re: VFO Knob replacement for zBitx posted
Thank you for sharing. ?I was going to use the ultra low profile knob for the trusdx and trim the shaft way down. ?
Ryan
Kk6dzb
|
Re: Does zBitx have SWR display?
Factory version of the frontpanel?firmware needs to be updated, and while you are it , do a ./update for the zbitx software as well.?
Mine doesn’t seem to do that. I’ve never seen a power output or SWR there.
73,
Paul, N8HM When you TX, you'll see power and SWR:  This snapshot is from the manual, available here:
On Wed, Apr 2, 2025 at 11:06?AM Nigel Evans M0NDE via <nigel.m0nde= [email protected]> wrote:
Just Curious if the zBitX has any SWR monitoring or display?
?
Regards,
Everett-WB9FUW
|
Re: Zbitx RPI SD-card image needed
Build a new SD-card (abour 32Gbyte) with a flasher-software like Balena Etcher.?
Download the Image and unzip it First.
--
Tilman D. Thulesius
SM0JZT / Sweden
|
Re: Video: Timing problems with zBitx internal keyer
Unfortunately exactly the same with my zBITX.
?
Gerald - HB9CEY
|
Re: Video: Timing problems with zBitx internal keyer
Yep, it’s missing a lot of your leading dots, suggesting that the sampling just ?isn’t fast enough. ?So your W started with dashes, and a lot of other characters are similarly mangled
?
?
It was also very disconcerting when it didn’t work right on the sBitx before, once the sampling went up much faster it became very nice?
?
Hopefully this will all get eventually settled out; We did on the sBitx , but it took a long time. ?Mike johnshoy was the solution
?
kx4z?
?
?
|
Re: Waiting for the zBitx to start…
I had to re-load mine two or three times and it finally started booting up (Tnx HB9CEY).
|
Re: Zbitx RPI SD-card image needed
How do I restore the image?
?
Leo? AI5II
|
Enable Bluetooth on the desktop turn on your keyboard and tell Bluetooth to scan for devices. ?You can then pair from there. ?On Linux I usually have a problem where Bluetooth wants to repeatedly disconnect from the device until the first reboot. ?After that works fine.?
|
Re: Waiting for the zBitx to start…
I had already executed this command without success.
I had already executed this command, without success. Everything is still as shown in the pictures.
toggle quoted message
Show quoted text
Am 02.04.2025 um 20:30 schrieb Ashhar Farhan via groups.io <farhanbox@...>:
? On that prompt, type
./build sbitx
Hallo!
After updating the zBitx software and firmware, the zBitx no longer starts properly. Repeating the update does not work..
?
What can I do to get the zBitx working?
?
vy73
Frank
<IMG_1714.jpeg> <IMG_1715.jpeg> <IMG_1709.jpeg>
|
Video: Timing problems with zBitx internal keyer
|
Re: Waiting for the zBitx to start…
On that prompt, type
./build sbitx
Hallo!
After updating the zBitx software and firmware, the zBitx no longer starts properly. Repeating the update does not work..
?
What can I do to get the zBitx working?
?
vy73
Frank
|
Hello everyone,
I understand that the zBitx has Bluetooth onboard the Raspberry Pi. Is there a way I can set up my Bluetooth keyboard with a track mouse to the Raspberry Pi on the zBitx? Any suggestions would be appreciated.
?
Thanks Everyone,
Robert, AG6LK?
|
Waiting for the zBitx to start…
Hallo!
After updating the zBitx software and firmware, the zBitx no longer starts properly. Repeating the update does not work..
?
What can I do to get the zBitx working?
?
vy73
Frank
|
I use these to help dissipate the excess heat. Slap them on back and let them do their job.?
Also use on Xeigu 6200.
?
?
?
|
What was your order number?
|
Ryan,
?
I'm sorry to hear that the zBitx arrived with a crack. I'm guessing the parcel had a rough journey to your location. Can you share some photos of the radio and the packaging with us. You can email it to us at support at HFSignals dot com.
?
I will share the STL files for the case soon.?
?
73,
Ragav
|
VFO Knob replacement for zBitx posted
Hello All,
I wanted a dimpled knob for the front of my zBitx, so I turned to Thingiverse to find a suitable knob and adjust the size to what I wanted and 3D printed my own in black PLA. The knob I've remixed is 10mm tall and 30mm in diameter, and will sit low to the front panel of the radio if you [very carefully] trim the length of the rotary encoder shaft. Please be careful to not bend the shaft of the encoder as you are doing this.
?
I've shared the files and full trimming instructions here
73 de VE6LK
|
Re: Does zBitx have SWR display?
Ensure your software and firmware are at the latest versions. I also have found a power cycle helps with this.
|
Hi Farhan I loaded firmware 1.06 and I am very happy the chugging sound has gone from cw reception. This afternoon listening on ssb 20m I did notice some less pronounced chugging sounds. I will try and add this to the github bugs list. Thanks for the fast cw fix. 73 Nigel MW0NDE?
I have fixed the two issues of zbitx on CW. The new update has good keying with Iambic keyer and the cw decode noise is now gone as well. To get this update, you have to: 1. Flash the new firmware (the firmware version is now 1.06). The firmware is available from? 2. Update the new software on the raspberry pi, the latest version with the CW keyng fixed is 3.051 (or later). Here is Jose, VU2JOS sending CW with the new firmware update.
With this, I hope we have moved on with CW issues. - f ?
|
Tilman, SM0JZT
Nigel Evans M0NDE