开云体育

Hi Chuck, If the relay is truly sticking, then replacement would be the only option.? If by "sticking" you mean that it will not go back or is delayed, going into receive mode after transmitting then

Is there a fix for the Rx Tx relay sticking?

Sunil, As Loris is interested, so am I in looking at the Nano code for the Easy Bitx that I purchased. I too am not able to find the code files in the files folder of this board.? All of the build

HI Sunil ... I'm not able to found the folder: ... /easy bitx vfo bfo code/ ,,, and are not possible to download all sketch .ino ! Please i'm very interested in these files for my EASY-BITX. Best

HI Sunil ... I'm not able to found the folder: ... /easy bitx vfo bfo code/ ,,, and are not possible to download all sketch .ino ! Please i'm very interested in these files for my EASY-BITX. Best

The one that was supplied since day 0 did not have this name. The sketch sent on email had this. Let me check the 11 files loaded post and see what it has to offer. PS to everybody. The si5351 is

The name Earnest was done by me for a customer unfortunately when compiling again it was not deleted and the compiled software sent to you had this name. The DDS works fine for me and many of my

I am also suggestive of the fact kit is not bad! the firmware is poor! Quality of PCB is outstanding for that matter! Also, the firmware copy supplied on email when flashed writes Earnest on the radio

I can provide you with the 'STOCK' Firmware for dissection that has been mailed to me by Sunil. I am unsure, why he is not posting it online. I wont be posting it here any way or uploading it anywhere

Sunil, Your file VFO_BFO_DDS.ino? uses the Si5351 library from etherkit. Here are the many different releases of the etherkit Si5351 library: https://github.com/etherkit/Si5351Arduino/releases Since

The following files have been uploaded to the Files area of the [email protected] group. * /EASY BITX FILES/AGC.pdf ( /g/BITX20/files/EASY BITX FILES/AGC.pdf ) * /EASY BITX

The following files have been uploaded to the Files area of the [email protected] group. * /Building-Easy-Bitx-Ver-1.pdf ( /g/BITX20/files/Building-Easy-Bitx-Ver-1.pdf ) *By:* Sunil

I've done it a different way using a PIC, but no reason it couldn't be adapted to any other micro controller like an Arduino https://www.vk5tm.com/homebrew/freq_switch/freq_switch.php (

Sunil, I'm convinced you have a solid product that works well. It fills a need, as HFSignals no longer sells a single band rig. Experimentation is encouraged, and I rather enjoy trying to figure out

In case anyone is curious about this business of the BFO moving when the VFO is changed: If it is a library issue causing the Si5351 to tune a common vco that is used for both for VFO and BFO, then

Bill There are no unworthy questions, each of us should admit to learning something here. Team Would not it be logical to host bitxmap at HFsignals?? One could invite buyers to add themselves to the

Jerry we provide a working DDS unit using si5351 which is tested with Freq counter . Now If any one has doubt on the DDS he is supposed to check the Freq output of vfo and bfo . Out here the builder

Hi, I would make sure you board is well grounded.? The cases are often painted very well so the standoffs and screws never make electrical contact.? Clean off the paint in the inside where the

Sunil's firmware as programmed into the Nano he ships with each radio is fine. He has sold plenty of them, and they work. I still don't know what you have done, or what you are doing. On scant

Bill KB3YV From what you posted, your uBITX is a V-5. There are not a lot of differences between V-3, V-4, V-5, and V-6. Most of the factory changes were focused on FCC compliance. There are several