Re: Issues with ordering the BITX40
Could this be the Raduino link?
73
Ken VA3ABN
|
Re: Antuino support group opened -- early antuino question
I have ordered my Antunio, and am waiting for delivery, anxious to try it out .? The above comment from Don raises one question for me:? Is it a VNA or SNA.? As I understand the difference is that the VNA measures the phase angle as well as the magnitude of the impedance, an SNA just measures the magnitude of the impedance.? in reading the description on the HF Signals Web Page it states SNA capabilities.
As far as output, you can get a Smith Chart from a VNA, not from an SNA.
So the question is if the hardware would support a VNA application, and and if so does the software provided have both the real and imaginary values of the impedance?
73
Evan
AC9TU
|
Dave
I sense we have thrown lots of choices at you.? Except for playing with IF shift, implementing an audio filter is easiest - with many low cost choices around.? Note in most respects the design architecture is very similar across v3, v4 and v5.? v5 was a larger change with a different IF selection for the SSB crystal filter.?
Many of us have rigs with 4915 kHz xtal filters made from cheap xtals.? Sounds like it could be installed in parallel with the 12 MHz filter without needing relays -- I should have thought of that - but we need a rig control to command the ubitx to 'Receive CW' to change the oscillator functions as Asher describes.?
Except in a major contest maybe, I find the audio filter is entirely sufficient with the way ubitx receive gain is distributed.? You might find CW transmit behavior a bit strange but it works fine once you are used to it.?
Curt
|
Re: Antuino support group opened -- early antuino question
Ashhar and Jerry -- thank you so much for the reply and info.? I better understand the general antuino application.? It is not a inline SWR/pwr meter, but it does a thousand other equally or more important jobs.? I'm always borrowing VNA from club members.? When I get a Antunio, I can stop being a pain in the neck to others. hahah.
P.S. I showed your email to my wife, and breathlessly exclaimed...look at this...Ashhar wrote to me!!!!? I did a little dance and told her I would never delete his email. [Obviously I need to get out more, but it is nice to have a few heroes out there, and you fit the bill. So a thousand thanks for all you've accomplished for all of us.? Okay, now I will stop sucking up. hahah.]
Don
km4udx
|
Re: Issues with ordering the BITX40
I have just checked this link
On Wed, Aug 14, 2019 at 3:25 PM MVS Sarma via Groups.Io <mvssarma= [email protected]> wrote: At the 2nd link, below the photo you can see "BUY" button. Us e it to rea h ordering page.
On Tue, 13 Aug 2019, 11:25 pm Jerry Gaffke via Groups.Io, <jgaffke= [email protected]> wrote: I'm still not seeing any way to buy a raduino from .
I see that the home page describes the "uBitx":
???
When I click uBitx at the top it takes me to a different page for the "MBITX":
???
Those two pages describe the same radio with most of the same section headers,
but give significantly different information.
I sort of know what's going on here, but have no idea which page is more current
without spending 15 minutes carefully comparing the two.
I suggest that the homepage just have a brief summary of all the various products:
? Bitx40, uBitx, Raduino, Antuino
plus a "Buy" button for all of them, a description of the company, and where to find the forum.
A page for each should fully describe the product, and tell us what the previous versions
of that product were.? For example, the Raduino page should make it clear that the previous
version was for the Bitx40 only, and that the connector has been changed to accommodate both
the uBitx and the Bitx40.? Also a pointer to where firmware and schematics and such are archived.
We get lots of traffic here in the forum wondering about versions of the various products,
how to plug a new Raduino into a Bitx40, what version of Bitx40 they have,
mods they should do, how and when to contact hfsignals.? That should all be on the website.
Jerry, KE7ER
On Fri, Aug 2, 2019 at 05:52 PM, Ashhar Farhan wrote:
I think that paypal has tweaked something and the old style button had stopped working. I will fix the raduino too.
- f
|
Ash
Does this option work on the V3 or V4 radios as well. Now to source more data on this option.
Evan
Yes as I mentioned I have the nextion display on most of my ubitx radios. I noticed that the IF shift when slid from one side to the other can make certain tones disappear and reappear I guess I should move it to one side or the other and see if I can use it to isolate. I assume it is a one way shift on the receive side only.
Thanks to all that wrote thoughtful replies.
toggle quoted message
Show quoted text
On Mon, Aug 12, 2019 at 08:10 PM, Ashhar Farhan wrote:
The ubitx has an option for narrow band filter. There are pins to install it.
The way it works is a bit of a hack :
1. The CW filter is at a different frequency. Let's imagine it is at 4.915
MHz. It is installed parallel to the 11.059 MHz SSB filter.
2. When choosing CW filter, you have to switch the second conversion
oscillator from 56.059 Mhz (45 + 11.059) to 49.915 Mhz (45 +4.915). Shift the
BFO to 4.914500 (According to your taste of CW tone).
Apart from designing the crystal filter, this hack is mostly about software
changes.
|
Re: Issues with ordering the BITX40
At the 2nd link, below the photo you can see "BUY" button. Us e it to rea h ordering page. On Tue, 13 Aug 2019, 11:25 pm Jerry Gaffke via Groups.Io, <jgaffke= [email protected]> wrote:
I'm still not seeing any way to buy a raduino from .
I see that the home page describes the "uBitx":
???
When I click uBitx at the top it takes me to a different page for the "MBITX":
???
Those two pages describe the same radio with most of the same section headers,
but give significantly different information.
I sort of know what's going on here, but have no idea which page is more current
without spending 15 minutes carefully comparing the two.
I suggest that the homepage just have a brief summary of all the various products:
? Bitx40, uBitx, Raduino, Antuino
plus a "Buy" button for all of them, a description of the company, and where to find the forum.
A page for each should fully describe the product, and tell us what the previous versions
of that product were.? For example, the Raduino page should make it clear that the previous
version was for the Bitx40 only, and that the connector has been changed to accommodate both
the uBitx and the Bitx40.? Also a pointer to where firmware and schematics and such are archived.
We get lots of traffic here in the forum wondering about versions of the various products,
how to plug a new Raduino into a Bitx40, what version of Bitx40 they have,
mods they should do, how and when to contact hfsignals.? That should all be on the website.
Jerry, KE7ER
On Fri, Aug 2, 2019 at 05:52 PM, Ashhar Farhan wrote:
I think that paypal has tweaked something and the old style button had stopped working. I will fix the raduino too.
- f
|
Re: Antuino support group opened -- early antuino question
The Antuino looks like a useful tool, well packaged.
I plan to get one.
But it won't be a replacement for your MFJ? power meter and SWR meter.
As Farhan pointed out, it would be very inconvenient to keep the Antuino tuned into
the frequency of the transmitter, the Antuino only sees one frequency at a time where
the MFJ is broadband.? And while the Antuino can measure the SWR of your antenna,
I don't think it can measure the SWR of an antenna while the transmitter is connected.
It could be used to measure the power coming out of a transmitter if you have
an appropriate resistive attenuator between the transmitter and the Antuino.
A small wire antenna on the Antuino might be used instead of the attenuator, but
the signal level seen by the Antuino will then vary with frequency and distance and
where your cat happens to be sitting.
Be very careful if using the Antuino around a transmitter, it would be easy
to feed it too much power and blow it out.
Jerry, KE7ER
?
toggle quoted message
Show quoted text
On Tue, Aug 13, 2019 at 06:50 PM, Ashhar Farhan wrote:
Don,
The answer is yes, but ... the Antuino needs to be tuned within 10 khz of the ubitx to receive and display the modulation.
Being as sensitive as it is, you dont even need to connect it with the tap. A small piece of wire in the RF IN will pick up thr ubitx transmission.
- f
?
Hide quoted text
?
On Wed 14 Aug, 2019, 1:24 AM Don - KM4UDX, < dontAy155@...> wrote: I have an early question (even before the support groups gets up and running...hahaha)
Is the Antuino able to be left in line with a tap & pad or something as a semi permanent basis to my uBITX? Right now I have an old MFJ power/SWR meter hooked up after the uBITX and before the antenna.? Is there a way to replace the swr/pwr meter with the? Antunio?
thanks!
Don
km4udx
|
Lots of magic in that Ubitx manager.... Enjoy!
Mark
|
Re: Antuino support group opened -- early antuino question
Don, The answer is yes, but ... the Antuino needs to be tuned within 10 khz of the ubitx to receive and display the modulation. Being as sensitive as it is, you dont even need to connect it with the tap. A small piece of wire in the RF IN will pick up thr ubitx transmission. - f
On Wed 14 Aug, 2019, 1:24 AM Don - KM4UDX, < dontAy155@...> wrote: I have an early question (even before the support groups gets up and running...hahaha)
Is the Antuino able to be left in line with a tap & pad or something as a semi permanent basis to my uBITX? Right now I have an old MFJ power/SWR meter hooked up after the uBITX and before the antenna.? Is there a way to replace the swr/pwr meter with the? Antunio?
thanks!
Don
km4udx
|
Re: What is the current version board? I have been away from the forum for awhile
The version differences are driven by hardware changes.
Harmonics have been reduced by a different board layout for the low pass filters.
Spurs reduced through a 90mhz low pass filter addition between the if stages.? Best would be do download the information from HF Signals web site.
The other change is to the SSB fcrystal filter.? The center frequecncy was changed from 12 mhz to 11.055 mhz to reduce interference from so of the Nano clocks that are close to 12 mhz (the USB converter).
With out the hardware changes, the code would not work, and there is not significant changes in operation other than in the calibration procedure.? The new firmware goes into transmit mode to set calibration, so a dummy load or 10 mhz antenna is required.
Above are what I remember, and I may have missed some significant changes, especially to the firmware, as after I go my v5 board running, I quickly installed the kd8cec firmware and Nextion display.
All of the test that I have done so far indicate that the harmonics are solved with the changes.? I do no have a good enough spectrum analyzer to verify the spurs, though others have reported significant reductions.
73
Evan
AC9TU
|
Re: What is the current version board? I have been away from the forum for awhile
How and where do you download the new version?
|
oops thanks for the input makes sense to me looking forward to it arriving? many thanks? dave c
|
On Tue, Aug 13, 2019 at 12:54 PM, Evan Hand wrote:
I agree with Don, Dean and Skip.? I have built 2 version 4 and 1 version 5.? The first went smoothly because I did follow the steps in Don's message.? The second one I had issues with because I jumped into the mods before I had the rig working.? The last one I followed the formula and had no issues.
Start with the base, get it working, then start on the mod filled journey.
73
Evan
AC9TU
|
Re: Antuino support group opened -- early antuino question
I have an early question (even before the support groups gets up and running...hahaha)
Is the Antuino able to be left in line with a tap & pad or something as a semi permanent basis to my uBITX? Right now I have an old MFJ power/SWR meter hooked up after the uBITX and before the antenna.? Is there a way to replace the swr/pwr meter with the? Antunio?
thanks!
Don
km4udx
|
I agree with Don, Dean and Skip.? I have built 2 version 4 and 1 version 5.? The first went smoothly because I did follow the steps in Don's message.? The second one I had issues with because I jumped into the mods before I had the rig working.? The last one I followed the formula and had no issues.
Start with the base, get it working, then start on the mod filled journey.
73
Evan
AC9TU
|
Dean and Skip speak wise truth. Do what they suggest, and your path will be fruitful.? ?
Every builder I know who rushed into adding the AGC board, or adding the spur reduction mod, or added a fancy external mic, or changed the relays, or or or had a MUCH harder time of it, and typically they give up in frustration, and uBITX never got happy on the air.?
So, build it as suggested in a pizza box, or plastic box, or anything that is easy. It is much more important to leave the physical rig exactly as designed, and then move on to loading the CEC software so you gain rig control for WSJTX or FLDGI, or HRD, or whatever software you use which controls the rig.?
So, in short,
1) build it as is, tweak BFO as needed,
2) load CEC software including memory manager
3) get your digital mode or logging application of choice to exercise uBITX rig control
4) use the radio (lots)
5) then, and only then, mod based on what needs YOU experienced in step 4 above.
Enjoy.
Don
km4udx.
|
Symptom: SSB audio is unreadable. When tuning the VFO, SSB signals are heard "off-frequency" then the audio "goes away" as the frequency gets closer to the correct frequency.
Solution: Perform the BFO calibration procedure.
Outcome: Receiver audio sounds great!
73,
Jim KX4TD
|
Antuino support group opened
?
I have taken the bull by the horns and opened a support group for the
Antuino..
?
?
?
Good Luck
?
73 Steve
?
G1KQH
|
Many tnx. ?It is working. ?Now find out how Ubitx manager works and what i cando with it. ?
|
_Dave_ AD0B
Jim Willis