Re: uBITX Firmware (CEC) 0.30 released (Test version).
#ubitx
Jason.
Thanks for your information.
Can you send me your settings?
If you send me the set value, I will test it together.
CW Speed (5th Menu),
CW TX-> RX Delay (5th Extra Menu),
CW Start Delay (6th
By
Ian Lee
·
#41506
·
|
Re: uBITX Firmware (CEC) 0.30 released (Test version).
#ubitx
Nope, it is still there. Just not as bad.
By
Jason Matonis
·
#41505
·
|
Re: uBITX Firmware (CEC) 0.30 released (Test version).
#ubitx
OK,
I think I figured it out if the CW TX->RX is set 140 or up you get the second dit/ dah when you release the paddle.?
73
Jason
KB2SDR
By
Jason Matonis
·
#41504
·
|
Re: uBITX Firmware (CEC) 0.30 released (Test version).
#ubitx
Hello,
I am enjoying ver 1.01 of the firmware very much. When I wired up a paddle with the 2.2k resistor on the dit and 10k on the dah. I notice an extra dit/dah when using the paddle.?
Not sure if
By
Jason Matonis
·
#41503
·
|
Re: No power increase with higher voltage?
I should have made note that all my tests in the opening message were in to a dummy load and reading on a dual-needle wattmeter with a 30w full scale reading. No reverse power was seen.
I tried
By
Vic WA4THR
·
#41502
·
|
Re: No power increase with higher voltage?
If the idling current is set high it may be possible that the two RFC's in
the
IRF510 stage are saturating, making them look more like wires than like
inductors.
_._
By
Arv Evans
·
#41501
·
|
Re: Help with wiring the audio, mic, and key jacks
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...
By
Michael Hagen
·
#41500
·
|
Re: I am new at this
David:
Vince is right. Get the rig working with the original setup and then
think about changing things.
There are 3 or 4 good sources for updates, all in several versions
which fix bugs or add new
By
John Backo
·
#41499
·
|
Audio Jack Wiring - Followup and Solution
Well, I ohmed the jacks out and went by the pictures and got it working. I wish the wireup
instructions had a several pictorial diagrams of the wiring on the jacks. The problem was
the numbering on
By
Mike Lichtman <tchrme@...>
·
#41498
·
|
Re: No power increase with higher voltage?
Vic:
Is there any difference in the distance achieved with QSO's
using 12v. vs 24v? Or is there any difference in the reported
received S level when using 24v vs 12v?
There are several possible
By
John Backo
·
#41497
·
|
Help with wiring the audio, mic, and key jacks
I am confused wiring to the jacks. The standard jack terminal no.s do not seem to apply to the wiring pictorial.
Do I go by the jack terminal no.s or the way the wires are connected in the pictures?
By
Mike Lichtman <tchrme@...>
·
#41496
·
|
Re: Tah dah!
I like it.?
I have fond memories of an Oldsmobile station wagon with the same design flair.
By
Doug W
·
#41495
·
|
Re: AGC kits
By
Joe Puma <kd2nfc@...>
·
#41494
·
|
Re: AGC kits
read the link
________________________________
Sent: Friday, February 9, 2018 4:15 PM
To: BITX20@groups.io
Subject: Re: [BITX20] AGC kits
Do you have a list of the components by designation Ex: R1,
By
N8DAH
·
#41493
·
|
Re: Tah dah!
Sweet.? I used the same case but I really like the wood front panel idea.? And a popsicle mic.
By
V Zecchinelli <n1vin@...>
·
#41492
·
|
Re: AGC kits
Do you have a list of the components by designation Ex: R1, R2, C1, C2.
The pcb does not show values only designations.
By
Ed Kelley
·
#41491
·
|
Display Backlight Adjustment
I'm sure somebody's already done this...
By
Arvo W0VRA
·
#41490
·
|
Re: Tah dah!
Mine isn't even here yet and I already know that I should have ordered 2,
one in production and one in pieces.
By
Rob Snow
·
#41489
·
|
Re: Tah dah!
Congratulations!
Time to take it apart and modify it.
???? Bob?? KD8CGH
By
Bob Benedict, KD8CGH
·
#41488
·
|
Tah dah!
And it worked the first time!
By
Arvo W0VRA
·
#41487
·
|