开云体育

joe i saw your posted message on my blog. and Thank you very much for youer suggestion. Most of the wsjt-x portable work is done. It was a little late because i had to work with uBITX

Bill Thanks for using this firmware. At first I wanted to make uBITX a real radio, so I started to put only the most basic functions. As I worked on it, I got a lot more fun with the opinions of the

Philip I am going to put uBITX into the case finally this week.Until now it was open for testing. I will cut off the power line of USB like you. And to fix the Arduino Nano reset problem, i will also

Matjaz Thanks for interresting. I saw the schematic you attached. It seems to have only an encoder and a function key. I do not test it, but I guess. so My guess might be wrong. My guess is that

Just a reminder! I'm probably not going to make it on for either session today. The flu shot apparently didn't work! Have fun! -- John - WA2FZW

hello Ian I have problem too use software 0.27 for uBitx. To load in arduino nano use Xloader and your hex file. But when conect power , first have on display mesage about version and then CW

What Cesar has not told us other than he has some great antique guns is that he has 6600 function generator. He also has a pico scope. I've been trouble shooting via whatsapp which is faster than

I know I'm late to this party but you cannot swap crystals on nano board without first using a atmel programmer to burn the fuse bits that tell what freq it will be using or you will brick your

Further tests and head scratching. ? Since I replaced the Arduino and mounted it on female headers I decided to do more tests to try to answer some of the leads and questions in the thread. ? I used

I have no idea what your sets of pins are.? Read this post to understand the relay pin numbering,? and how the rail labeled "TX" gets connected to 12v when you press the PTT switch to transmit.? ?

hello all? First poster;?? k3 suppose to have voltage all the time?? on rec first set of pins have none. second set/3 have 11.8 v last one no voltage. on trans.1st third and fourth set of pins

SSB only draws current when you speak into the microphone or in the case of digital, transmit a frequency.? Sent from Yahoo Mail. Get the app

Met Bjarne in a Birds of a Feather session at an OOPSLA(Object Oriented Programming Systems and Languages) conference in the Pacific Northwest. just to further name drop, I also met Ester Dyson at the

Okay, so I am not going bonkers over the changes in amperage. Something else that I noticed, psk31 on 40m pulls 1.5 amps, but feld-hell pulls only 0.8 amps...any idea why? -- ---------- N5WLF,

It's in the right range. The draw and output depend heavily on frequency. You can see the draw I measured key down into a dummy load at different frequencies in this post

Ah, that explains! In your case you'd need to round to the nearest 10 Hz. at line 481: ultoa((frequency + 50), b, DEC); // construct the frequency string change to: ultoa((frequency + 5), b, DEC);

USB requirements are rather stringent. Unless the 12 MHz crystal has changed radically in frequency, it should be pretty much left alone. (If it has changed or if it interferes, the best solution is

Thanks, Allard. I'm thinking perhaps to eliminate the +50 in my version since I am displaying an extra digit in normal mode. Do you know where (what line) that rounding takes place? 73,

Thanks Nick I will put up the further details on the news item on uBITx.net I am sure that your mod will be widely adopted for those of us who are aflicted by nearby AM broadcast stations. Mike --

UBITX V.272U -FRONT PANEL VIEW TOP INSIDE VIEW From atmega 2560? - 3 cables for clocks and 6 pin harness to ubitx 2 cables for SI5351 Lower left are 2 voltage down converters - 1 adjusted to 9v for