开云体育

---------- Forwarded message ---------- Date: Thu, 24 Jun 2004 10:22:26 +0530 To: arvevans@... Cc: farhan@... Subject: RE: BITX20, 40 or 75 M versions? dear arv, you have

I realize that I'm late getting into the group. Jameco (http://www.jameco.com/) has 10 MHz, 50 ppm crystals for $0.69/10, $0.59/100+, $0.49/1000. I think that corresponds to 0,38 L/10, 0,32 L/100,

The two extra sets are already accounted for! Seems I should have bought more spares, but I didn't really want to be stuck with components and be unable to do anything with them. I can get more

I did a little bit of poking around, and found that Mouser offers these at USD$1.50 each, or $1.24 in 100-pc quantities. For stateside users, it might be possible to set up a volume buy and then

I have now placed the bulk order for BITX20 components. I have emailed all those who asked for the components. If you haven't heard from me then I have probably forgotten you in which case

Reminder everyone: deadline for orders for all the semiconductors + crystals + tuning capacitor + trimmers is tomorrow at 12:00 GMT (13:00 UK Time). 73 Hans G0UPL

Dear Friends, I have just read all of the original posts to this new yahoo group, and I am delighted. This is a fun and exciting project and I am recommending it to all my friends in the Austin QRP

Hans, Please will you go ahead and include me in your order? I want the complete set of components as shown in your list below. Please email me your postal address details and I will get the total

Generally tap washers are used to fix leaky taps/faucets. They are made of teflon or nylon and vary from 1/2 inch dia to 3/4 inch dia, with a hole in the centre which varies frfom 3mm to 4mm in

Thanks to Mark and Paolo for their replies. I am clear on "tap washers" now and learned about "jubilee clips" too. I would have called them "hose clamps". 73 Heinz, OE5EEP

Hans, I witheld my original cheque pending your Email of today. I should like the full list as per your Email of 10.51 today and will pay by Paypal as you suggest in uk pounds Many thanks jack ford

Don't forget Mark, it's a bifilar transformer with two windings, not just a single winding with a centre tap. 73 Hans G0UPL http://www.HansSummers.com

I can't get 2N3866 at any of my usual suppliers either! For now I'll keep the 2N2219A in the list. 73 Hans G0UPL http://www.HansSummers.com

Pete, what VFO stabilizer are you using? Is it Huff Puff? I love Huff Puff, and definitely intend to build a simple stabiliser for the BITX20 when I have the rest of it working. See my Huff Puff page

Finally here's a full list of what I can order for you from Rapid Electronics http://www.rapidelectronics.co.uk. Prices are the Rapid prices, i.e. no profit for G0UPL :-( Postage is the price of a

--- In BITX20@..., "Mark Jones" <Mark@H...> wrote: Hi, just joined the group. Hope I will have some time to build this great RIG soon. > Hmm, good question. An American asked me recently

On Mon, 21 Jun 2004, david.g3ryp wrote: > I've taken the measurements you suggested and indeed it was the driver whose output was low - only about 1 volt peak. I was using BC549s throughout and

Many thanks for the advice Farhan. I've taken the measurements you suggested and indeed it was the driver whose output was low - only about 1 volt peak. I was using BC549s throughout and although

i calculated 3uH on each winding. - farhan

the 2N2218 is a fatter type of 2N2222. you can use the 2N3866 instead. they are expensive in india. but they might be easier to find elsewhere. - farhan