Perhaps we need to have a sep[erate power wired from the building input thro a metal conduit and provicde an additional emi filter for that right at the load point.. Obviously the equipment ground would be connected to that .
?? Perhaps these are general precautions even the manufacturer prescribes.
On Thu, Feb 8, 2018 at 10:23 PM, Dave Bottom <ars.kd6az@...> wrote:
Even my Novice 75W transmitter would light the hall light at night each time I keyed the rig.
Reversing the switches at each end of the hall made it non resonate on 40M. ?
Probably saved some RF to be radiated too.? LOL
Dave WI6R
On Feb 7, 2018, at 9:15 AM, Michael Hagen <motdog@...> wrote:
Yes, it depends on
input Z of the amps.? I remember tube amps.?? I built a big
stereo in the 60's, they had Hi Z so low values worked.? I
have a great story....... My neighbors had a water heater
system with a big water holding solar panel on the roof.? When
I fired up the SB200 or 220, it cycled their water pump.? They
figured it out!?? They heard me Yelling on the Mic during a DX
Contest!? They put 2 and 2 together.
I had to go on the
roof and put .1uF? on all their control switches and wiring!??
It was a perfect 20 Ant. up there.
73's
Mike
?
On 2/7/2018 8:44 AM, Mvs Sarma wrote:
Mice,
?I had these experiences that old? Inveterted audio
electronic telephones instruments called secraphones
installed for VIPs? close to Radio Transmitters? used
to misbehave.
?We immediately used to have a capacitor across the Mic
module and telephone line Inop=put close to active
components to byepass RF.
?You are right that even 1000pF would do.
?But afterall the audio at Volumen control point is coupled
with 1 to 5uF capacitors.
?hence i thought even 0.1uF would not deteriorate audio.? The
induction could be internal to amplispeaker also and thro
power mine that powers the ampli speakers.
?Thu8s? I suppose that byepaasing audio at volume cotroll
stage is better.
?regards
?sarma
?vu3zmv
??
Regards
MVS Sarma
?
On Wed, Feb 7, 2018 at 8:53 PM, Michael
Hagen <motdog@...>
wrote:
Might try
looping lead (leads?) to amp thru a ferrite, or get
the split clamp on ones, close to were it goes in
the amp?
Wrap up in a
coil any extra length of the cable.? Makes a common
mode choke.
As Sarma
says, maybe a 100 - 1000 pF bypass on each input?
73's
Mike, WA6ISP
On
2/7/2018 6:45 AM, Mvs Sarma wrote:
i imagine that Prabha jee
?Pleace a 01.1uF capacitor on ech channel,
at the middle pin of Violume control to
ground. It would byepass the RF induced in
the speaker connecting cable.
? Aduio would disappear.
All the best
?sarma
?vu3zmv
Regards
MVS Sarma
?
On Wed, Feb 7, 2018 at 7:00
PM, Praba Karan <vu3dxr@...>
wrote:
external amplispeaker...
i heard audio even volume down bottom.
Virus-free.
On Wed, Feb 7, 2018
at 6:18 PM, Mvs Sarma <mvssarma@...>
wrote:
Is it external speaker or
external amplispeaker?
Regards
MVS Sarma
?
On Wed, Feb
7, 2018 at 5:05 PM, Praba Karan <vu3dxr@...>
wrote:
This
issue is from microbitx
--
D.Prabakaran?
VU3DXR
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."Mike@...
--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."Mike@...