Re: Chinese clones - not working as expected
#ATU-10
Hi David
That would be brilliant
73,
Jon G4TSN
toggle quoted message
Show quoted text
----- Original Message ----- From: "David Fainitski" <rolin791@...> To: < [email protected]> Sent: Thursday, November 18, 2021 2:23 PM Subject: Re: [ATU100] Chinese clones - not working as expected #ATU-10 Hi. OK, I will implement zero position for L and C. That is not a big problem. Also I can do a manual tuning L and C with additional buttons + and - connected to Ext port .
|
Re: Chinese clones - not working as expected
#ATU-10
Hi David, thanks a lot for your efforts! Vy 73 de
toggle quoted message
Show quoted text
Am 18.11.2021 um 15:23 schrieb David Fainitski <rolin791@...>:
?Hi.?
OK, I will implement zero position for L and C.
That is not a big problem.
Also I can do a manual tuning L and C with additional buttons + and - connected to Ext port .
|
Re: Chinese clones - not working as expected
#ATU-10
Hi.?
OK, I will implement zero position for L and C.
That is not a big problem.
Also I can do a manual tuning L and C with additional buttons + and - connected to Ext port .
|
Re: #ATU-10 VK3PE build complete.
#ATU-10
Hello Ellis,
How much output did/do You use in FT8 via the ATU-10, I think 5W is possible to much?
73 de Frank PH2M
|
I can only think about the swr bridge being different with the potentiometers. The pic controller adc is the same. I have looked for alignment information but unfortunately.?
Instead the easiest alignment is to run full power and measure the max voltage towards the adc. Depending on the pic controller you need to adjust or 4 or 5 volt. I don't remember the exact value unfortunately.
For the rest the circuit is exactly the same as the atu-100. Just bigger components, larger PCB traces.?
I don't understand why the pic controller code should be different. Except for the high power factor and bridge coil turns.?
Hope you can find the information as eu2av shared with you.
Best regards Onno Op wo 17 nov. 2021 20:25 schreef sq7bcn < sq7bcn@...>:
Hi Tim,
When it comes to the EE data, I can make a copy of
it, because I have worked out the topic ... see the attachment.
But it's not just about EE, so EU2AV wrote to me that there are
even changes in Flash, I don't remember what it was about,
whether it was a power measurement gear or something else, and
that's why it was done on version 2.7 because in version 3, x
broaks memory space.
That's why I'm asking, maybe David will suggest something?
Pozdrawiam ,
Marek SQ7BCN
73
W dniu 2021-11-17 o?19:15, Tim pisze:
Hi Marek,
3.2 works fine in the ATU1000
BUT... Make a copy of the eeprom data 1st. ( this is what I
didn't do with mine and it took a while to work out the cell
values )
This is because the EU2AV version uses different L & C for
the tuner and you will also need to know the turns ratio for
cell 31 and check that cell 30 is set to 01. All that is in your
eeprom data
When you update the s/w to 3.2 you will have to input the cell
data you copied from your old version and write that to the PIC.
You can then do a read of the PIC to make sure that all is as
expected and then export that as a hex file as a backup for
just-in-case.
regards
Tim
On 17/11/21 7:33 am, sq7bcn wrote:
Hi,
I made a 1500W tuner according to the EU2AV scheme (PIC 16F1938
processor).
David N7DDC firmware based on old version 2.7.
Question for David,
is it possible to do it on software version 3.1 or 3.2 and
display the correct power value?
Hex in the attachment.
Marek SQ7BCN
_
--
VK2XAX : QF56if : ITU59 : CQ30 : BMARC : WIA
|
Re: #ATU-10 VK3PE build complete.
#ATU-10
Good news then!
Sent from my Samsung Galaxy S7 smartphone.
toggle quoted message
Show quoted text
-------- Original message -------- From: "Ellis Birt (G7SAI) via groups.io" <ellis.birt@...> Date: 18/11/21 7:05 am (GMT+10:00) Subject: Re: [ATU100] #ATU-10 VK3PE build complete.
I found a short that was causing the battery life issues.
|
Re: #ATU-10 VK3PE build complete.
#ATU-10
I found a short that was causing the battery life issues.
|
Hi Tim,
When it comes to the EE data, I can make a copy of
it, because I have worked out the topic ... see the attachment.
But it's not just about EE, so EU2AV wrote to me that there are
even changes in Flash, I don't remember what it was about,
whether it was a power measurement gear or something else, and
that's why it was done on version 2.7 because in version 3, x
broaks memory space.
That's why I'm asking, maybe David will suggest something?
Pozdrawiam ,
Marek SQ7BCN
73
W dniu 2021-11-17 o?19:15, Tim pisze:
toggle quoted message
Show quoted text
Hi Marek,
3.2 works fine in the ATU1000
BUT... Make a copy of the eeprom data 1st. ( this is what I
didn't do with mine and it took a while to work out the cell
values )
This is because the EU2AV version uses different L & C for
the tuner and you will also need to know the turns ratio for
cell 31 and check that cell 30 is set to 01. All that is in your
eeprom data
When you update the s/w to 3.2 you will have to input the cell
data you copied from your old version and write that to the PIC.
You can then do a read of the PIC to make sure that all is as
expected and then export that as a hex file as a backup for
just-in-case.
regards
Tim
On 17/11/21 7:33 am, sq7bcn wrote:
Hi,
I made a 1500W tuner according to the EU2AV scheme (PIC 16F1938
processor).
David N7DDC firmware based on old version 2.7.
Question for David,
is it possible to do it on software version 3.1 or 3.2 and
display the correct power value?
Hex in the attachment.
Marek SQ7BCN
_
--
VK2XAX : QF56if : ITU59 : CQ30 : BMARC : WIA
|
Re: Good kit supplier for Europe ?
Many thanks, this is more than I asked for but will be extremely useful as I actually need the same thing as what SP5GNI has done, so it is "off the shelf" for me!
73
Yannig, F4IUJ
|
Hi Marek,
3.2 works fine in the ATU1000
BUT... Make a copy of the eeprom data 1st. ( this is what I
didn't do with mine and it took a while to work out the cell
values )
This is because the EU2AV version uses different L & C for
the tuner and you will also need to know the turns ratio for cell
31 and check that cell 30 is set to 01. All that is in your eeprom
data
When you update the s/w to 3.2 you will have to input the cell
data you copied from your old version and write that to the PIC.
You can then do a read of the PIC to make sure that all is as
expected and then export that as a hex file as a backup for
just-in-case.
regards
Tim
On 17/11/21 7:33 am, sq7bcn wrote:
Hi,
I made a 1500W tuner according to the EU2AV scheme (PIC 16F1938
processor).
David N7DDC firmware based on old version 2.7.
Question for David,
is it possible to do it on software version 3.1 or 3.2 and display
the correct power value?
Hex in the attachment.
Marek SQ7BCN
_
--
VK2XAX : QF56if : ITU59 : CQ30 : BMARC : WIA
|
Thanks to everyone who helped me with this, I now have a much better understanding of my unit.
regards
Tim
--
VK2XAX : QF56if : ITU59 : CQ30 : BMARC : WIA
|
#ATU-10 VK3PE build complete.
#ATU-10
Hi, I have completed my build and made my first FT8 QSOs today.?
The battery life seems poor, but I may have managed to get low capacity batteries.? There are batteries available on eBay In the UK with wires attached, but they are non-rechargeable so be careful.? I chose to use AA battery holders to avoid soldering to the batteries.? This may give me problems using the case I have ordered.
I was worried about the usb socket shorting to the micro USB pins so I stuck a bit of Kapton tape to the socket before attaching.
My TP4056 boards did not have suitable capacitors (micro USB variety) or only 1 (USB C variety) do I had to order those.
I have no 220K resistors so R19 is two in series manhattan style.
Programming the PIC16F1454 in circuit using my picking required power from the USB.? ?A temporary wire from the 3.3v supply from the programmer to the chip gave me an over current error.
All in all I am very pleased and have another complete set so I will be building another.? A third will have to wait for more relays and mosfets.
I still have 12 spare PCBs if anyone in the UK is interested.? I have sent some to the EU and I am waiting to hear if they arrived OK and if VAT had to be paid.
73 de Ellis G7SAI
|
Re: Chinese clones - not working as expected
#ATU-10
Hi David, yes I know the test firmware and it’s very helpful for checking relays. However can we have a special state to bypass all the inductors or capacitors? My understanding is with the current test firmware, if we switch between inductor and capacitor testings, there is always one inductor or capacitor activated and that interferes with VNA measurements on individual component. I’m thinking perhaps adding L0 and C0 in the loop to indicate bypassing all the inductors/capacitors. Thanks again for your great work! 73 de kn6pzo
|
Re: Chinese clones - not working as expected
#ATU-10
Hi, All
Please notice that my GitHub contains a special test firmware. I hope it would be helpful in issues fixing.
|
Re: Programming & compiling from github source code
Hi, All
I am not a professional programmer and I don't use GitHub in a right way. Oftenly the code changes with no version changing.?
Please use the sources as is and as you want.
|
Re: Good kit supplier for Europe ?
Many thanks. That helped a lot! Vy 73 de Rolf? Am 17.11.2021 um 14:51 schrieb Onno PA1AP <pa1ap68@...>:
toggle quoted message
Show quoted text
? I used the attached schema as the reference. It works well. Regards Onno Op wo 17 nov. 2021 14:44 schreef Rolf Schroeder < rolf@...>: Hi Onno, how did you build the feeding splitters? I want to replace my SGC tuner by an ATU 100 and save a little amount of copper hi.? Vy 73 de Rolf, DL8BAG Am 17.11.2021 um 14:23 schrieb Onno PA1AP <pa1ap68@...>:
? I am using DC through coax and it works. You only have to set the tuner to "auto" once and it will remember this setting until you perform a reset or push another button.?
Regarding reliability I have no information.?
Regards Onno Op wo 17 nov. 2021 14:20 schreef Yannig - F4IUJ via <yannig.robert= [email protected]>: Hello all,
I am a bit confused by the dozens of offers one can find on internet for an ATU100, is there a "trusted seller" that you would recommend ? Alternatively, are they all good or are there suppliers to definitely avoid ?
Also I want to double check, is it OK to operate the ATU remotely ? It is to put on a boat so the ATU will be below deck where the antenna exits which is hard to access, the plan is to simply switch on the power supply before operating and to let the ATU do its work.
73s
Yannig, F4IUJ
|
Re: Good kit supplier for Europe ?
I used the attached schema as the reference. It works well. Regards Onno Op wo 17 nov. 2021 14:44 schreef Rolf Schroeder < rolf@...>:
Hi Onno, how did you build the feeding splitters? I want to replace my SGC tuner by an ATU 100 and save a little amount of copper hi.? Vy 73 de Rolf, DL8BAG Am 17.11.2021 um 14:23 schrieb Onno PA1AP <pa1ap68@...>:
? I am using DC through coax and it works. You only have to set the tuner to "auto" once and it will remember this setting until you perform a reset or push another button.?
Regarding reliability I have no information.?
Regards Onno Op wo 17 nov. 2021 14:20 schreef Yannig - F4IUJ via <yannig.robert= [email protected]>: Hello all,
I am a bit confused by the dozens of offers one can find on internet for an ATU100, is there a "trusted seller" that you would recommend ? Alternatively, are they all good or are there suppliers to definitely avoid ?
Also I want to double check, is it OK to operate the ATU remotely ? It is to put on a boat so the ATU will be below deck where the antenna exits which is hard to access, the plan is to simply switch on the power supply before operating and to let the ATU do its work.
73s
Yannig, F4IUJ
|
Re: Good kit supplier for Europe ?
Hi Onno, how did you build the feeding splitters? I want to replace my SGC tuner by an ATU 100 and save a little amount of copper hi.? Vy 73 de
toggle quoted message
Show quoted text
Am 17.11.2021 um 14:23 schrieb Onno PA1AP <pa1ap68@...>:
? I am using DC through coax and it works. You only have to set the tuner to "auto" once and it will remember this setting until you perform a reset or push another button.?
Regarding reliability I have no information.?
Regards Onno Op wo 17 nov. 2021 14:20 schreef Yannig - F4IUJ via <yannig.robert= [email protected]>: Hello all,
I am a bit confused by the dozens of offers one can find on internet for an ATU100, is there a "trusted seller" that you would recommend ? Alternatively, are they all good or are there suppliers to definitely avoid ?
Also I want to double check, is it OK to operate the ATU remotely ? It is to put on a boat so the ATU will be below deck where the antenna exits which is hard to access, the plan is to simply switch on the power supply before operating and to let the ATU do its work.
73s
Yannig, F4IUJ
|
Re: Good kit supplier for Europe ?
I am using DC through coax and it works. You only have to set the tuner to "auto" once and it will remember this setting until you perform a reset or push another button.?
Regarding reliability I have no information.?
Regards Onno Op wo 17 nov. 2021 14:20 schreef Yannig - F4IUJ via <yannig.robert= [email protected]>:
Hello all,
I am a bit confused by the dozens of offers one can find on internet for an ATU100, is there a "trusted seller" that you would recommend ? Alternatively, are they all good or are there suppliers to definitely avoid ?
Also I want to double check, is it OK to operate the ATU remotely ? It is to put on a boat so the ATU will be below deck where the antenna exits which is hard to access, the plan is to simply switch on the power supply before operating and to let the ATU do its work.
73s
Yannig, F4IUJ
|
Good kit supplier for Europe ?
Hello all,
I am a bit confused by the dozens of offers one can find on internet for an ATU100, is there a "trusted seller" that you would recommend ? Alternatively, are they all good or are there suppliers to definitely avoid ?
Also I want to double check, is it OK to operate the ATU remotely ? It is to put on a boat so the ATU will be below deck where the antenna exits which is hard to access, the plan is to simply switch on the power supply before operating and to let the ATU do its work.
73s
Yannig, F4IUJ
|
Rolf Schroeder
Frank PH2M
Onno PA1AP
Tim
