What does a cross slide mounted indicator show when the front &
rear of the spindle are checked? It sounds like the HS is not
parallel to the ways, easiest measurement is spindle parallelism to
cross slide.
How much spindle run out is there?
Have you tried a test cut with the cross & compound gibs locked
down? Your chatter complaint makes me suspect one or both of them
may be moving during a cut.
Quick check for bed mounting distortion is to loosen the bolts &
try to rock the lathe; if it rocks, use feeler gauges or indicator to
determine the shim thickness for the non-contacting foot.
Roy
--- In 7x12minilathe@..., Nick DeFeo <ntdefeo@y...> wrote:
Good Morning Bob:
Here is what I have so far: Stock is 3/4" 12L14, HSS 3/8"
cutting tool - sharpened & honed, 3 jaw on hs and live center in ts.
With stock either chucked or supported by ts, I have indicated top
and rear of stock and corrected alignment using shims between the bed
and bench. Bolts are snug, but not tight to permit adjustment if
required. Whether the stock is held with just the 3 jaw, or supported
with the ts, the lathe still cuts a taper towards the hs in the
neighborhood of .02". I am using a Starret square base to level the
unit fore/aft and side to side. All readings using the level are dead
center, with no parallax error (all readings taken from top dead
looking down at the vial). Should I invest in a more precise level to
ensure these reading are true? I have checked for alignment at the
hs, center of the bed and ts areas. While it has been several years
since I have used a lathe, am I overlooking something minor here? All
carriage and compound gibs are properly adjusted and lubricated.
While cutting, I have used several fluids with the same results:
WD40, 10W oil with STP, and even kerosene. Are these lathes that far
out of alignment from the factory, or is this due to
shipping/handling? There was no damage to the carton or the lathe
when received, and I wonder if this unit should be returned for a new
one. While I am not opposed to making corrections/adjustments to get
acceptable results, this has been quite perplexing, to say the least.
Best regards, Nick
Bob Sunley <rosunley@s...> wrote:Check list time:
What are you cutting, type of metal/plastic, diameter and length.
How is it chucked, 3 jaw, 4jaw, between centers or combination.
Type of cutter, hss, carbide, a u-grind or factory insert.
Speed setting, power or manual feed.
Chattering and cutting tapers are two totally different problems.
Which do you want to fix first.
Cutting tapers can indicate a warped bed or tailstock not set
properly depending on how you are holding the workpiece.
which way is the taper?
Chattering can be any number of problems, wrong/no cutting lube,
wrong feed rate, tool height set wrong, wrong type of tool, too
fine a
cut, too agressive a cut, assorted gibs not adjusted properly, etc.
etc, etc.
Solidly mounting the lathe can cause tapered cuts as well if it
warps
the lathe bed
Need lots more info on exactly what you are doing.
Bob
On 9 Dec 2002, at 21:23, ntdefeo ntdefeo@y... wrote:
After setting and checking my Homier 7X12 lathe 9 ways to sunday,
I
am still turning tapers! As carriage is advancing towards the hs
assembly, the hs cutting tool starts to chatter, no matter what
adjustments are made. Is it possible that the bed it bowed/warped
in
such a manner that this machine should just be returned for a new
unit? I have never run up against such a perplexing problem. All
adjustments have been checked and rechecked for accuracy. Unit is
solidly mounted on a bench. Has anyone else run across this
problem?
Any comments? suggestions? short of heaving it into the trash?
To unsubscribe from this group, send an email to:
7x12minilathe-unsubscribe@...
Your use of Yahoo! Groups is subject to
To unsubscribe from this group, send an email to:
7x12minilathe-unsubscribe@...
Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.
---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now
