开云体育

  1. Yaesuft301d
  2. Topics

Yaesu ft301d FOR SALE

Bob Isselhard
 

I have an FT-301D for sale.? It receives all modes all bands.? This one has an 11 meter crystal in the AUX position? I have the original Yaesu power cord and plug but no microphone.? I see power out on RTTY and AM.? I have solved the very common display burnout issue with the $200 board and parts from Elcon that completely replace the troublesome digital display failure issue.? I can send pictures to you if you post here indicating an interest and give me a contact method.? I'm asking $250 plus shipping but that is negotiable within reason.? I have two many radios and will be liquidating them one by one.? It may need some more work but lets face it, the burnout of the display segments is the biggest drawback with these and that is solved.? I will check here every day for any replies. Thanks for reading?
73, Bob, K5INW?
 

> I see power out on RTTY and AM.?

I was given a FT-301S with a similar symptom... generates RF on AM but not CW/SSB. Different modulation circuitry for AM. If this is a frequent problem, I'd love to get a hint where to look.

73 Chuck K4RGN
Bob Isselhard
 

Well Chuck, since I have no mic for it, I don't know about AM.? And I didn't try it on CW.? If you have confirmed yours doesn't xmit on those modes, I suggest you look at the IF UNIT, specifically Q403 and it's associated circuitry.? Also, it could be "dirty" contacts from the board to the main board.?
 

Hello Bob,
If item is still available, I am mildly interested.

If you can send/post a couple of pics: front, back and top, we could start with that. You don't mention a manual or if there are any optional filters installed. I am assuming there aren't.

It's not clear to me if you know whether or not there is no output on SSB or that you can't test because of no microphone.

Did you install the Elcon, or was it there when you obtained it?

Thanks,
Jim
Bob Isselhard
 

Jim:? Thanks for your interest and questions.?

I will get some pix posted later today after I go out to the ham shack and turn the radio ON.

I don't have a hard copy manual.? I d/l a .PDF off the internet.? Pics a bit indistinct compared to hard copy but the rest is quite useable.

I will have to check for the presence of any optional filters.?

I don't know if SSB has output because I have no microphone to test with.? There wasn't one with the radio when I got it.? I have inquiries out in my area to find one.

I installed the Elcon replacement board and components and did the voltage and frequency calibration as well as the setup with the Philips remote I have with my Philips flat screen TV.

I also have the original Yaesu board and display segments.? I may have some extra display segments around here somewhere.? I haven't looked for them since I installed the Elcon replacement.

Hope this helps.? Bob
Bob Isselhard
 

Pic of radio and filters (all three).?


On Sat, Nov 11, 2023 at 10:20 AM Bob Isselhard via <robertisselhard=[email protected]> wrote:
Jim:? Thanks for your interest and questions.?

I will get some pix posted later today after I go out to the ham shack and turn the radio ON.

I don't have a hard copy manual.? I d/l a .PDF off the internet.? Pics a bit indistinct compared to hard copy but the rest is quite useable.

I will have to check for the presence of any optional filters.?

I don't know if SSB has output because I have no microphone to test with.? There wasn't one with the radio when I got it.? I have inquiries out in my area to find one.

I installed the Elcon replacement board and components and did the voltage and frequency calibration as well as the setup with the Philips remote I have with my Philips flat screen TV.

I also have the original Yaesu board and display segments.? I may have some extra display segments around here somewhere.? I haven't looked for them since I installed the Elcon replacement.

Hope this helps.? Bob

 

Thanks Bob.

Private message sent.

-Jim

1 - 7 of 7