开云体育

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Xiegu-X6100
  2. Topics

R1CBU firmware 0.22.0 ???

 

开云体育

?
If I put the SD-card with R1CBU FW into the computer USB ... I get two things :
DATA-F and BOOT-D .
To where I have to copy the new? x6100_r1cbu_0.22.0.tgz? ???
?
At firts comes a message when I insert the sd-card? : The card must format . The card would have a problem/issue ...
?
73 , Jens / HB9JOI
?
+++
?
SD card X6100 R1CBU
?
+++
?
?

From: g.dyuldin@...
Sent: Friday, August 16, 2024 3:48 PM
Subject: Re: [xiegu-x6100] R1CBU firmware 0.22.0
?
On Fri, Aug 16, 2024 at 04:39 PM, Jens wrote:
How it is to install ?
Only create a SD-Card with Balena-Etcher ?
?
If you already have an SD card with one of the previous version - insert SD card to your computer, copy attached file to the DATA drive, insert card to transceiver and boot it.

SD card X6100 R1CBU.jpg

 

On Fri, Aug 16, 2024 at 05:34 PM, Jens wrote:
If I put the SD-card with R1CBU FW into the computer USB ... I get two things :
DATA-F and BOOT-D .
To where I have to copy the new? x6100_r1cbu_0.22.0.tgz? ???
?
DATA (F:)
?
At firts comes a message when I insert the sd-card ?: The card must format . The card would have a problem/issue ...
One of the partition of SD card have ext4 file system - it's doesn't supported by Windows. This is fine
 

开云体育

?
Ok , done ... seems to work the X6100 .
At start-up is shows 0.22.0
?
73 , Jens / HB9JOI
?
+++
?
?

From: g.dyuldin@...
Sent: Friday, August 16, 2024 4:42 PM
Subject: Re: [xiegu-x6100] R1CBU firmware 0.22.0 ???
?
On Fri, Aug 16, 2024 at 05:34 PM, Jens wrote:
If I put the SD-card with R1CBU FW into the computer USB ... I get two things :
DATA-F and BOOT-D .
To where I have to copy the new? x6100_r1cbu_0.22.0.tgz? ???
?
DATA (F:)
?
At firts comes a message when I insert the sd-card? : The card must format . The card would have a problem/issue ...
One of the partition of SD card have ext4 file system - it's doesn't supported by Windows. This is fine
 

when I put the SD card on the computer(windows 10), it shows?NO partitions-disk management?shows the card as drive E, with no partitions
When it's convenient, perhaps a new .img file can be posted
 

It should be an SD card with previous version of the R1CBU firmware (I guess, 0.20.0 should be fine). You can download it here -

 

If you're going to upgrade, power off the x6100, take the?existing microsd card?out of the x6100 and open it on your computer. You'll see a bunch of folders. Just past the .tgz file right there. Then reinsert the microsd card in the x6100 and power up. It will take a bit longer than normal to boot up (but it won't show anything special, doesn't say "upgrading...", etc). Once it's booted, you're now on 0.22.0


On Sat, Aug 17, 2024 at 1:14?PM Chris DL6SEZ via <saiteklilo50=[email protected]> wrote:

[Edited Message Follows]

You are such an arrogant p...r so what?
?
 

开云体育

Hi
One General question for this firmware:
To run ft8 rx/tx, which time has to be set (local or utc) that it syncronises?

vy 73 de Klaus, DC2JR

Von meinem iPhone gesendet

Am 18.08.2024 um 14:09 schrieb Leland Olney via groups.io <lee@...>:

?
If you're going to upgrade, power off the x6100, take the?existing microsd card?out of the x6100 and open it on your computer. You'll see a bunch of folders. Just past the .tgz file right there. Then reinsert the microsd card in the x6100 and power up. It will take a bit longer than normal to boot up (but it won't show anything special, doesn't say "upgrading...", etc). Once it's booted, you're now on 0.22.0

On Sat, Aug 17, 2024 at 1:14?PM Chris DL6SEZ via <saiteklilo50=[email protected]> wrote:

[Edited Message Follows]

You are such an arrogant p...r so what?
?
 

Can I ask where you see the version number at startup?
?
?
 

On Sun, Aug 18, 2024 at 05:48 PM, dc2jr wrote:
One General question for this firmware:
To run ft8 rx/tx, which time has to be set (local or utc) that it syncronises?
Application expects that transceiver time is UTC. Setting another timezone only makes ADIF will contain wrong QSO time.
Max time skew for correct FT8 is ~2 seconds. Less is better. But it will work, if you time skew is N times 15 seconds
 

As soon as it finish booting up, the version number briefly appears in the center of the screen and then goes away. After it goes away the radio is now then ready to use.
Again, the normal working screen shows up and then in the middle of the screen, the version number shows very briefly and the disappears. So keep an eye in the middle of the screen at the end of the booting up sequence.

1 - 10 of 10