开云体育

IC7300 CW with FlDigi 4.2.06

Anders Georgsson #38048 I had it working fairly well but now, suddenly - something has happened so as my IC7300 is transmitting the tone, the radio releases the PTT , pauses and reengages the PTT and continues!? ? I read and followed the instructions for using FLRIG and FLDIGI together but it's just not working like it used to. ? It used to trigger the transmitter and FlDigi would pulse its tones and once finished - it'd switch back to receive mode.. I don't believe I used to have to enable break-in or full break-in.. If I don't do that now - then I can HEAR the tone but it is never transmitted. Any suggestions?
Jean Christophe Barbera All Messages By This Member #38049 开云体育 Check if the macros have TXID. If so, TXID ?and rxid must be enabled. F5ind 73 Chris? Jean-Christophe BARB?RA toggle quoted message Show quoted text Le 18 mars 2025 à 01:54, Anders Georgsson via groups.io <anders.georgsson@...> a écrit?: had it working fairly well but now, suddenly - something has happened so as my IC7300 is transmitting the tone, the radio releases the PTT , pauses and reengages the PTT and continues!? ? I read and followed the instructions for using FLRIG and FLDIGI together but it's just not working like it used to. ? It used to trigger the transmitter and FlDigi would pulse its tones and once finished - it'd switch back to receive mode.. I don't believe I used to have to enable break-in or full break-in.. If I don't do that now - then I can HEAR the tone but it is never transmitted. Any suggestions?
Anders Georgsson #38052 Hmm - did have <# TXRSID:on> in my macro (which should mean that it isn't executed, right?) but I removed that line all together and it is still behaving this way. The only button I have turned on at the top right in FlDigi is "Spot"... ? I even tried turning that off but it still toggling the between TX/RX during the transmission of code... ? I am not sure if I mentioned this in my original post but I'm using FLRIG to control my rig (so I can control it remotely) - if I use it's CW Keyer - the radio pulses the signal rather than keeping the transmitter on and playing the tone thru the integrated sound card as well? ? ?
Jean Christophe Barbera All Messages By This Member #38053 开云体育 I'm new to this software. I sometimes have difficulties. I've noticed that it's sometimes necessary to close the software for changes to take effect. Jean-Christophe BARB?RA toggle quoted message Show quoted text Le 18 mars 2025 à 16:12, Anders Georgsson via groups.io <anders.georgsson@...> a écrit?: ? Hmm - did have <# TXRSID:on> in my macro (which should mean that it isn't executed, right?) but I removed that line all together and it is still behaving this way. The only button I have turned on at the top right in FlDigi is "Spot"... ? I even tried turning that off but it still toggling the between TX/RX during the transmission of code... ? I am not sure if I mentioned this in my original post but I'm using FLRIG to control my rig (so I can control it remotely) - if I use it's CW Keyer - the radio pulses the signal rather than keeping the transmitter on and playing the tone thru the integrated sound card as well? ? ?
Anders Georgsson #38054 When in doubt - restart ?? IT rule #2 ?? Yes - i've tried that as well. On Tue, Mar 18, 2025 at 12:32?PM Jean Christophe Barbera via <jc-barbera=[email protected]> wrote: toggle quoted message Show quoted text I'm new to this software. I sometimes have difficulties. I've noticed that it's sometimes necessary to close the software for changes to take effect. Jean-Christophe BARB?RA Le 18 mars 2025 à 16:12, Anders Georgsson via <anders.georgsson=[email protected]> a écrit?: ? Hmm - did have <# TXRSID:on> in my macro (which should mean that it isn't executed, right?) but I removed that line all together and it is still behaving this way. The only button I have turned on at the top right in FlDigi is "Spot"... ? I even tried turning that off but it still toggling the between TX/RX during the transmission of code... ? I am not sure if I mentioned this in my original post but I'm using FLRIG to control my rig (so I can control it remotely) - if I use it's CW Keyer - the radio pulses the signal rather than keeping the transmitter on and playing the tone thru the integrated sound card as well? ? ? -- Anders Georgsson (352)316-0258 cell? KZ4JN/WSDF851
K2JJK All Messages By This Member #38055 Restart. Yes. It's in the document. Making changes to the rig control especially and that's where most of the problems occur. best, jim/K2JJK On Tue, Mar 18, 2025 at 2:38?PM Anders Georgsson via <anders.georgsson=[email protected]> wrote: toggle quoted message Show quoted text When in doubt - restart ?? IT rule #2 ?? Yes - i've tried that as well. On Tue, Mar 18, 2025 at 12:32?PM Jean Christophe Barbera via <jc-barbera=[email protected]> wrote: I'm new to this software. I sometimes have difficulties. I've noticed that it's sometimes necessary to close the software for changes to take effect. Jean-Christophe BARB?RA Le 18 mars 2025 à 16:12, Anders Georgsson via <anders.georgsson=[email protected]> a écrit?: ? Hmm - did have <# TXRSID:on> in my macro (which should mean that it isn't executed, right?) but I removed that line all together and it is still behaving this way. The only button I have turned on at the top right in FlDigi is "Spot"... ? I even tried turning that off but it still toggling the between TX/RX during the transmission of code... ? I am not sure if I mentioned this in my original post but I'm using FLRIG to control my rig (so I can control it remotely) - if I use it's CW Keyer - the radio pulses the signal rather than keeping the transmitter on and playing the tone thru the integrated sound card as well? ? ? -- Anders Georgsson (352)316-0258 cell? KZ4JN/WSDF851

Previous Topic Next Topic