The DT400R can be connected to the command station via loconet for
programming. If you are usingthe DB150 as your command station
however, yo will be limited to the DB150 programming features (no CV
readback, no separate programming track).
Or you can re-option your DCS50 as a command station.
6 of one......
Doug
--- In WiringForDCC@..., "Ron Massa" <ron@r...> wrote:
Doug: Thanks for the info! This is all still pretty new to me so
I
appreciate "experienced" advice. Can I connect the DT400R
throttle via
loconet (not in simplex radio mode) and use that for programming
instead of
switching the DCS50 back to command station mode? If not,
switching the
DCS50 back to programming mode in the rare occasion that I need to
program
doesn't seem like a big deal.
Regards,
Ronald A. Massa, Sr.
RMA Electronics, Inc.
35 Pond Park Road, Unit #12
Hingham, MA 02043
TEL: 781-749-9700
FAX: 781-749-9707
Email: ron@r...
Specialists in Vision and Imaging since 1986
-----Original Message-----
From: WiringForDCC@...
[mailto:WiringForDCC@...] On
Behalf Of Doug Stuard
Sent: Wednesday, December 14, 2005 2:44 AM
To: WiringForDCC@...
Subject: [WiringForDCC] Re: Expanding from a Digitrax Zephyr
system to a
Super Empire Builder system
The DCS50 can be optioned to separate the throttle and booster
functions (and disable the command station) so your DB150 can be
used as the command station. The DCS50 manyual describes how to
do
this.
The DB150 can feed your PM42 and the DCS50 can feed yet another
power district for a total of five.
Keep in mind that the DB150, when use as a command station CANNOT
read back CVs, so you may want to keep the DCS50 so you can switch
it back to command station mode for programming.
Doug Stuard
NVNTRAK
--- In WiringForDCC@..., "ahacman" <ron@r...> wrote:
Last year I purchased a Zephyr starter set with DCS 50 all-
in-
one command station/booster/throttle and use it to run my new
layout
(single power district running two locos on a small layout). It
works great! I just purchased a Radio equipped Super Empire
builder
set for my layout expansion currently under construction with
DT400R
throttle and DB150 command station/booster plus an additional
UT4R
throttle, a PM42, plus some other stuff (will probably expand to
6-
8
loco addresses max. with 2 or 3 users max. at a time).
My question is can I switch my Zephyr DCS 50 to a
throttle and booster only to run my original layout portion
(still
as a single power district) and use my new DB150 as my new
booster/command station driving the new expansion subdivided
into
4
new power districts? I will subdivide my expansion into 4 power
stations (main line, freight yard, side spurs, etc.) so I also
purchased a PM42. Do I have to reprogram my current two locos
to
run from the new command station? Since I will be greatly
expanding
my layout I think I would prefer to switch to the DB150 as my
command station now as it will offer more addresses, etc.
although
I
probably will never exceed the 10 max addresses of the Zephyr
DCS150
so I want to do whatever is easiest. Your advice is greatly
appreciated. Thank you.
_____
YAHOO! GROUPS LINKS
* Visit your group "WiringForDCC
<> " on the web.
* To unsubscribe from this group, send an email to:
WiringForDCC-unsubscribe@...
<mailto:WiringForDCC-unsubscribe@...?
subject=Unsubscribe>
* Your use of Yahoo! Groups is subject to the Yahoo!
<> Terms of Service.
_____
[Non-text portions of this message have been removed]
