开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
  1. Tinysa
  2. Topics

Failing Self Test after v1.4-159 upgrade #firmware_update #tinysa #ultra

 

Hi,

I've just updated firmware to v1.4-159 on both my tinySA and my Ultra and both failed self test after that.

TinySA reported "Test 7: StopBand Critical"



Ultra failed both Test 10 and 14, both reporting "Signal Level Fail"



Both units were tested using the longer ALSR-100 cable provided with the Ultra version.
I have also tried connecting both together, outputting a 300MHz, -5dBm signal from the tinySA and reading it at around -6,6dBm on the Ultra (wich seems about correct to me), when I tried doing this with the shorter cables (the one that came with the tinySA) the Ultra read -9.0dBm

Both units should be genuine as they were bought from Eleshop.eu following link from the wiki
tinySA was bought in May 2022, HW version: V0.3.1_EL
Ultra was bought in Dec 2022, HW version: V0.4.5.1

Have I broken something or missed some step?

Thanks!
--
//LMA//
RF Coordinator for live shows
 

On Mon, May 6, 2024 at 06:24 AM, <luca.marenco.96@...> wrote:
TinySA reported "Test 7: StopBand Critical"
This is not a fail but a "critical" which can be ignored.

Ultra failed both Test 10 and 14, both reporting "Signal Level Fail"
This is a possible LNA failure.
Restart, Connect in selftest configuration, enable the 30 MHz cal output and enable the LNA and post a photo or capture of the screen

?
--
Designer of the tinySA
For more info go to https://tinysa.org/wiki/
 

开云体育

Hi Luca,

Did you do a Clear Config then a Calibration before the Self Test?

HTH...Bob VK2ZRE


On 6/05/2024 11:24 pm, luca.marenco.96@... wrote:

Hi,

I've just updated firmware to v1.4-159 on both my tinySA and my Ultra and both failed self test after that.

TinySA reported "Test 7: StopBand Critical"



Ultra failed both Test 10 and 14, both reporting "Signal Level Fail"



Both units were tested using the longer ALSR-100 cable provided with the Ultra version.
I have also tried connecting both together, outputting a 300MHz, -5dBm signal from the tinySA and reading it at around -6,6dBm on the Ultra (wich seems about correct to me), when I tried doing this with the shorter cables (the one that came with the tinySA) the Ultra read -9.0dBm

Both units should be genuine as they were bought from Eleshop.eu following link from the wiki
tinySA was bought in May 2022, HW version: V0.3.1_EL
Ultra was bought in Dec 2022, HW version: V0.4.5.1

Have I broken something or missed some step?

Thanks!
--
//LMA//
RF Coordinator for live shows
 

Hi Erik and thanks for the answer

This is a capture with the LNA active


This one without the LNA

?

Thanks!
--
//LMA//
RF Coordinator for live shows
 

Yes, on both devices
--
//LMA//
RF Coordinator for live shows
 

Seems the LNA is no longer functioning.

--
Designer of the tinySA
For more info go to https://tinysa.org/wiki/
 

And what LNA is used in TinySA Ultra? It seems mine is also out of order. It does not pass tests 10 and 14.
 

See FAQ in WiKi
--
Designer of the tinySA
For more info go to

1 - 8 of 8