开云体育

Rob, There is an oblong hole in the back case near the jog switch.? Push the small thread loop through there (it may take a tiny tool to help), then thread the pick and lanyard through the small

Can somebody give me a clue about how you're supposed to attach the lanyard (with the little guitar pick on it)? I can't find anything to wrap it around, and the introductory videos never have a

Erik: Thanks for the new 1.76 firmware. I loaded it, and have discovered (as was suggested ) that my display is NG... that throws the error. So, I'll live without waterfall, the unit still performs

New FW release Version V1.1-76 Changes: - Corrected the bug that caused a hang after a failing display test. The display test is no longer the first test but test 11. Test 12 is now the attenuator

As the waterfall is also not working this "hang" is caused by an error in the self test when it detects it can not read correctly back from the display memory. I will correct this error in the next FW

Just had another look, the instant I hit the Self Test mode, I see (for a very small fraction of a second) a line of dots or dashes at the very top of the screen. They only exist for maybe 0.1 seconds

For the real TinySA with the white label, you can "laminate" the label with a piece of clear packing tape placed over it and carefully trimmed to fit the space with a sharp hobby knife. Recommended

Hello Erik, This test was with 1.1-75m freshy loaded.? ?My tinySA is HW V0.3? ? SN SA-20102809 The Level Cal works as expected, green progress "bar" etc, and completes. However, the Self Test

First run original TinySA. Firmware 75, both waterfall modes work OK, self test passes. 73 -Jim NU0C "Erik Kaashoek" <erik@...> wrote:

I expect the display test at the start of the self test fails. Let me try to simulate display failure and see how it behaves Do you see a single colored line appear at the top of the screen at the

Hello All: New tinySA user here, (I have a NanoVNA too).? My tinySA was from R&L, so should be real. I've had the unit for 3 weeks, worked well.? ?However, I have an odd issue when I load the

Back in another life I picked up some used SMA adapters from one of the regular hamfest vendors that seemed to be in good shape for just a few dollars. I looked up one of the Amphenol parts later and

Erik: Serial number is SA-20100478 Version: v0.3 tinySA_v1.1-12-gccc0fbe Kernel 4.0.0 Compiler gcc7.2.1 20170904

I upgraded mine to 1.1-75 and it shows that firmware version. Also corrects the modulation in FM Narrow and FM wide carrier frequencies. I used IMSAI Guy's YouTube video and it worked

I upgraded the firmware this morning to 1.1.74. No problems. Then I saw the firmware upgrade to 1.1.75, so I thought I'd upgrade to the most current version. Loaded it. Everything seemed to work

Yes, Zeenko is the store of Hugen who manufactures all genuine tinySA -- ------------------------------------------ For more info on the tinySA go to https://tinysa.org/wiki/

Any of the Asian connector will work up to 350Mhz without problems and whatever small impedance bumps or loss they have from 400Mhz to 1ghz is less than the problems in resolution that the analyzer

Zeenko store currently have tinysa for ?37 plus ?5 carriage which is about the cheapest available anywhere. These are genuine? They also sell the saa2N for a pretty good price, too. Steve L

Thank you, requested a refound and will re-order from zeenko store. If only I had found this information before. Also pity I gave the seller 5 stars (like most others) for his fast shipping and cannot

As listed on the wiki page the seller tool-box store sells clones and you have indeed received a clone. -- ------------------------------------------ For more info on the tinySA go to