开云体育

Since the noise source generates a very wide bandwidth signal, this causes the mirror suppression algorithm of the tinySA ULTRA mode to fail. When the scanning frequency is greater than 3GHz the IF

I hope you read the page on limitations of enabling the Ultra mode and measuring wideband or scanning signals.? The step at 3GHz is normal for the noise source you are using. With a noise source,

Hi Leif, THX for the plots. As a comparison on my ULTRA, I used a ViewTEQ 5-1000MHz noise generator with an in-line 10dB pad and obtained the following plots at 10MHz - 3GHz. NOTE: This is

I think you will find this interesting. https://youtu.be/X4dGaC0QiEw?si=mNBxCAPxbtktOPJq

There is an article in the Jan/Feb 2025 issue ?of the QEX (which is available to ARRL members) on how to build a low-cost tracking generator for the tinySA.? Perhaps an ARRL member in this group

I was browsing TinySa examples from https://tinysa.org/wiki/pmwiki.php?n=Main.Mixer TinySas? where directly coupled to each other.? May I ask, does it really work and can I make one TSA to output

The noise source is supposed to work at 12V,? but it runs very hot even at 10V. This is at 12V. I don't know how, but the problem may be at the source/Nose.

Sure, here it comes, all? two of them. Could a Wlan leak here, I didn't see the 2.4GHz peak? at first when my PC was off. (Clock on my SA is off.) The step shows on? PC too.

Hi Leif, Think we could get a screen shot of the "step" ? -----------------------------------------From: "Leif M via groups.io" To: [email protected] Cc: Sent: Wednesday January 1 2025

I? used? a 20dB attenuator between the noise source? and TinySa.

When I was (playing) testing with my Nose source noise source and TinySA, everything was fine at lower frequencies, but when the max frequency was 5GHz, there was a 10-20dB step at 3GHz. I don't think

Robert, glad you got it fixed. Hope you have a Happy and Productive 2025!!! Best Regards.....Ted (KD7AQO) -----------------------------------------From: "Robert K3RRR" To: [email protected] Cc:

*"We don't need any stinkin' driver!"* Bravo, Ted et al! I did indeed have BOOTLOADER as a device under "Other Devices." Like a dumbass, I had believed that since Windows 11 recognized the comport

If you are using a windows computer (especially WIN 11), this might be the issue. 1) If you can connect the device to the USB port (hear the "ding"), Go into Control Panel: Hardware: Device Manager -

After putting the tinySA in DFU mode, you need to use the small icon with two up-arrows to open the firmware update window. Then see if the DFU device shows up in the drop-down list in that window. If

Hi David, Thanks for the recommendation I am trying to use your suggestion of using the app but having a problem with "No valid DFU device found." PROBLEMS UPDATING FIRMWARE ON TINY SA ULTRA Powered

Hi everyone, I disassembled the device and successfully replaced U22 with AS179-92LF. My device now passes all self-tests and calibration. While disassembling, I broke the 4-pin battery connector (2

Robert, Under Windows-10 I've been using the TinySA-app v.1.1.20.1 without any problems. Cheers, David -- SatSignal Software - Quality software for you Web: https://www.satsignal.eu Email:

THD calculates the THD of the fundamental using the harmonics as visible in the scan. There seem to be no harmonics visible in your scan -- Designer of the tinySA For more info go to

When I study the ultra with version 187, and use measure->more->THD, whatever I move the marker, the THD always 0, can someone give me some suggestions?