Re: Delay due to damage
I ordered direct from Maggie on AliBaba with trade assurance Well packaged and arrived without any problems -- Clive - G7SVI
By
G7SVI
·
#1159
·
|
Phase noise of tinySA compared to Rigol DSA815
After seeing this video https://youtu.be/MCBrhxPQotU?t=152 I wanted to compare the phase noise of the Rigol DSA815 with the tinySA In the Rigol video the phase noise is measured at 10kHz distance and
By
Erik Kaashoek
·
#1158
·
|
Re: New to the group
Dear Walt, yes, one of the reasons for me getting the Tinysa is, not only can I put it in my pocket/ suitcase/ etc, as well as walk around with it to trace qrm, but I think I am going to have to
By
Stephen Laurence
·
#1157
·
|
Re: New tinySA control program for Windows
I tried V1.0.179 and was able to get a trace. Excellent work, Cathy, Erik, Herb et al!
By
stefan baartman
·
#1156
·
|
Re: New tinySA control program for Windows
Hi Erik, no reason in particular, I was trying all the options to see if I could get something to give me a trace.
By
stefan baartman
·
#1155
·
|
Re: Detecting a noise source
Hmmm, a difficult question to answer. It is in the (relatively) new wife¡¯s house, where I do not have any of my ham gear (I wonder why?). I did bring up a Clansman 320 backpack radio (40 year old hf
By
Stephen Laurence
·
#1154
·
|
Re: Detecting a noise source
Steve-- Did you sell the ham gear or the reclining chair??? Inquiring minds would like to know...
By
Larry Macionski
·
#1153
·
|
Re: Message for Kurt Poulsen
UPS You might refer to another activity off mine and not the 40 minutes video in Danish. The report/user guide in Dansk it being published in the Danish HAM Magazine OZ in few days and then I can
By
Kurt Poulsen
·
#1152
·
|
Re: Message for Kurt Poulsen
Hi Wayne I have fully occupied creating calibration kit files for the SAA-2N for both VNA-QT and NanoVNA-saver so have not found time yest It is also a major job to sound dubbing a live video to fit
By
Kurt Poulsen
·
#1151
·
|
Re: New tinySA control program for Windows
Hi Erik, Ah OK, understood, please keep up the good work. Regards, Martin
By
Martin
·
#1150
·
|
Re: New tinySA control program for Windows
As stated the conversion is not yet completed
By
Erik Kaashoek
·
#1149
·
|
Re: New tinySA control program for Windows
I'm a bit confused with respect to scattering parameters S11 and S21 being shown on the display, when being used as a SA. Regards, Martin
By
Martin
·
#1148
·
|
File /tinySA-app/tinySA-App.exe uploaded
#file-notice
The following files have been uploaded to the Files area of the [email protected] group. * /tinySA-app/tinySA-App.exe ( /g/tinysa/files/tinySA-app/tinySA-App.exe ) *By:* Erik Kaashoek
By
[email protected] Notification <tinysa@...>
·
#1147
·
|
Re: Detecting a noise source
You have an excellent tool to trace it. Set the span to scan ( some of) the interference frequencies, eg 3-14mhz. Put the telescopic aerial on the lower sma socket. Extend the aerial and see the noise
By
Stephen Laurence
·
#1146
·
|
Re: New tinySA control program for Windows
Here are my settings. TinySA is in LOW mode !!!!!!!
By
Erik Kaashoek
·
#1145
·
|
Re: New tinySA control program for Windows
Yes. The latest build is V1.0-91 and you are running V1.0-61 Pleas upgrade. Read the wiki for guidance how to upgrade
By
Erik Kaashoek
·
#1144
·
|
Message for Kurt Poulsen
Hi Kurt, Hope this finds you well. With regard to the User Guide you produced for your presentation about TinySA in Danish language. I think you indicated you may produce a copy in english, forgive me
By
Wayne Johnson
·
#1143
·
|
Re: New tinySA control program for Windows
Stefan. Why do you use TDR instead of? log mag S11?
By
Erik Kaashoek
·
#1142
·
|
Re: Correction Data Question..
HERB, Thank you kindly, Gentle Sir.. Bedtime for this Bozo but I'll give it a shot tomorrow.. Severe health issues (Heart and Lungs) means I go nowhere at the moment :-( Ham Radio is a great way to
By
David KK7SS
·
#1141
·
|
Re: New tinySA control program for Windows
Any possibility we have different version devices? Mine's Version info says: tinySA v0.3 Version: tinySA_V1.0_61_gff54300 Build Time: Aug 26 2020 - 09:13:04 Kernel: 4.0.0 [email protected]> wrote:
By
stefan baartman
·
#1140
·
|