The nanoVNA-app github source repository of OneOfEleven is not public.

On Wed, Sep 23, 2020 at 12:09 AM, Erik Kaashoek wrote:

Look in the file section of this group

It isn't there.? I already have the tinySA-App.exe, note that I mentioned above that I had got it to run in WINE.? I asked about the NanoVNA-app, because I wanted to see if there was any support for it that might give me a clue on how to get tinySA-App (running in WINE)? to access the USB serial port.? There doesn't seem to be any NanoVNA-app information on github, and apparently there is no support for it.

Look in the file section of this group

I looked on github for that NanoVNA-app, but didn't find it.? Can somebody steer me to the right place? I was able to run the tinySA-app that is based on it in WINE in Linux Mint 19.3, but couldn't get it to find the serial port.? Any pointers on that would be nice, too.? (Maybe it's on the github page that I couldn't find?)

Hi Erik, I updated to -91, thanks.

Thanks Kurt,
Really appreciate all your efforts, Ill keep a watch on here.
Cheers and kind regards
Wayne VK6EH

开云体育

I ordered direct from Maggie on AliBaba with trade assurance
Well packaged and arrived without any problems
--
Clive - G7SVI

After seeing this video

I wanted to compare the phase noise of the Rigol DSA815 with the tinySA
In the Rigol video the phase noise is measured at 10kHz distance and is about -85dBc/Hz
How about the tinySA?
Well, it is a bit worse, but not much: -83dBc/Hz

On Mon, Sep 21, 2020 at 06:14 PM, waltcates wrote:

Good morning?group,

?

I got my tinySA three days ago. I have downloaded tinysa.exe and paired my tinySA to a TAB PRO S tablet. I was guided to this site in a discussion about the tiny on another site. I got the tiny as a replacement for my 60-year-old HP141 that died again.....

Dear Walt,

yes, one of the reasons for me getting the Tinysa is, not only can I put it in my pocket/ suitcase/ etc, as well as walk around with it to trace qrm, but I think I am going to have to dispatch my HP141 anslysers - I have three of them with four different plugins, covering the whole available frequency range. I think the single most useful one is the 0-1.1ghz one, as it did not take too long to warm up and settle, and it was almost as easy to use as the 0-110mhz plug-in. AND I have not used them for over 5 years, so I would probably have to swap plugins and get the maintenance manual out. Nevertheless, I learned a lot from them.

The only problem is looking at close-in signals, such as ssb intermodulation and phase noise. To do this, even the HP141 0-110mhz plug-in needed to warm up before continuous retuning was required. Also, the 1-3ghz area is quite important (cellphones, wifi, microwave oven leakage etc) but I have got a Deepace KC 901s which can pass off as a handheld spectrum analyser as well as being a scalar network analyser (0-3ghz). The most recent version with 0-6ghz, vector capability and 1khz rbw is ?1600, so no chance to upgrade for me, and still probably not too effective to measure phase noise.

?HOWEVER, I have decided that when I need to do such work, I will have to spark up a pc and a sdr dongle. I have a rsp1 which I have got a rbw down to 50hz. The only problem is you need as much bench space and setting up as the HP141 needed. On the plus side, I can get rid of three boat-anchors.

steve L G7PSZ

I tried V1.0.179 and was able to get a trace. Excellent work, Cathy, Erik, Herb et al!

Hi Erik, no reason in particular, I was trying all the options to see if I could get something to give me a trace.

Hmmm, a difficult question to answer.

It is in the (relatively) new wife’s house, where I do not have any of my ham gear (I wonder why?). I did bring up a Clansman 320 backpack radio (40 year old hf military transceiver) a while ago but could not receive anything. I presumed it was the solar panels or the data over phone line, as it worked fine in the middle of a field. I did not have the TinySA then (or the nanovna, which can be used as a sort of spectrum analyzer).
Eventually we will move into my house, but probably without the reclining chair but with the Mrs (more use than a reclining chair, but more expensive to run). The problem is that the PSU is on the whole time (for the chair, not the Mrs, although installing an on-off switch, or at least a mute button is an interesting project to work on).

Steve L. G7PSZ

Steve--
Did you sell the ham gear or the reclining chair??? Inquiring minds would like to know...

开云体育

开云体育

On Tue, Sep 22, 2020 at 12:58 PM, Erik Kaashoek wrote:

As stated the conversion is not yet completed

Hi Erik,

Ah OK, understood, please keep up the good work.

Regards,

Martin

As stated the conversion is not yet completed