Re: New FW release: Big letter label info added
I just updated to 1.3331 and now I have no spectrum display at
all.?? The labels on the left and right are there but no waterfall
or analog graph
??
Does something need reset?
Thanks
Rich
On 1/10/2022 12:49 PM, Erik Kaashoek
wrote:
toggle quoted message
Show quoted text
New FW released
Version 1.3331
Changes:
- DISPLAY/LEVEL METER option added to show BIG letter marker info
This new feature will, when enabled, display the value of the
first active marker at the bottom of the graph in BIG letters
Let me know if it does not behave as expected
--
For more info on the tinySA go to
|
New FW release: Big letter label info added
New FW released Version 1.3331 Changes: - DISPLAY/LEVEL METER option added to show BIG letter marker info This new feature will, when enabled, display the value of the first active marker at the bottom of the graph in BIG letters Let me know if it does not behave as expected  --
For more info on the tinySA go to https://tinysa.org/wiki/
|
Re: What to do when a selftest fails
Someone it asked us to share Self-Test results ... here's mine ... 
|
Re: New FW release: Repaired remote control
Hi Erik.
Thank you for the quick response,? the tinySA gets? better and better!
??????? Joe.
|
Re: Calibration help after firmware update
Good catch, forgot to update the wiki with the updated correction command. You have to specify which correction table to use as there is now also a correction table for the high input
ch> correction
usage: correction low|high 0-9 frequency(Hz) value(dB)
ch> correction low
index frequency value
correction low 0 10000 6.0
correction low 1 100000 2.8
correction low 2 200000 1.6
correction low 3 500000 -0.4
correction low 4 30000000 0.0
correction low 5 140000000 -0.4
correction low 6 200000000 0.4
correction low 7 300000000 3.0
correction low 8 330000000 4.0
correction low 9 350000000 8.1
?
--
For more info on the tinySA go to https://tinysa.org/wiki/
|
Calibration help after firmware update
Hi all, think I'm making a rookie error but can't see it so could do with a pointer. ?I've just updated my unit to 1.3-330. ?This is my first time updating the firmware. ?I saved the leveloffset and correction?calibration?values before updating as documented in the . ?When trying to restore the correction values,?then the console is rejecting it due to an apparent syntax error:
ch> correction 0 10000 6.0
usage: correction low|high 0-9 frequency(Hz) value(dB)
|
New FW release: Repaired remote control
New FW release Version 1.3330 Changes: - Bug solved: Remote control does not react to mouse click --
For more info on the tinySA go to https://tinysa.org/wiki/
|
Re: New FW release: improved restore mode after power switch
Hello Erik.
The 'remote' way of operating the TinySA ( on the APP) stopped working,
? (I get auto refresh?? in the 'capture' mode but no response to trying to get the menu buttons on the PC screen).
TIA???? Joe.
|
Re: Trouble detected after the new “saving switch off” features.
#bug_report
Yes it is OK now. Thank you Erik for your work.?I also noticed that since the LO OUPUT feature does not exist in HIGH IN mode, it could perhaps be removed from the tinySA config high in mode menu and thus release free up memory (for new FW versions).
Thanks.
Toni
|
Re: Trouble detected after the new “saving switch off” features.
#bug_report
Toni, Can you test if the new release is OK? --
For more info on the tinySA go to https://tinysa.org/wiki/
|
New FW release: improved restore mode after power switch
New FW release Version V1.3229 Changes: - Bug solved: After restoring in high mode menu's are inconsistent - Bug solved: After restoring to output mode the MODE button goes back to the main menu --
For more info on the tinySA go to https://tinysa.org/wiki/
|
Re: Trouble detected after the new “saving switch off” features.
#bug_report
Thanks, the restore of modes other then low mode has not yet been well tested. WIll investigate --
For more info on the tinySA go to https://tinysa.org/wiki/
|
Trouble detected after the new “saving switch off” features.
#bug_report
Trouble detected after the new ?“saving switch off” ?features.
To replicate the trouble try that:
1.-MODE /SWITCH TO HIGH ?IN
2.-PRESET/STORE/STORE AS STARTUP
3.-MODE/ SWITCH TO LOW IN
4.-Switch the tinySA OFF and ON
There is a mismatch in the performance, the screen shows (or ?seems working) like in low mode, but other parts and menus seems working in high mode internally.
Toni
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
Hi guys.
If using win 10, when the device is plugged in with DFU mode then run windows update, look at other devices in the update optional update and it will find the STM driver and you can choose to install it. Windows will do it for you.
Hope that helps.
Joe G4XRZ
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
Thank you Dave, that is a good idea, never occured to me about
documenting it!
On 1/7/2022 5:20 PM, DAVE REISER wrote:
toggle quoted message
Show quoted text
Hi John,
?
Hallelujah, praise the Lord worked! The
only thing I found different was you said that you checked
the universal serial bus controllers for the boot loader. It
was in the universal serial bus devices not controllers..
That may be computer specific.
Anyway thank you very very much. If I get
the chance I'll document that with pictures, a little bit
more than what you did. If it's worth sharing I'll share it.
?
Kind Regards,
Dave
Dave Reiser
Phone:
301-216-5394
Mobile:
301-802-1929
Email:?
davereiser@...
520 Russell Avenue, Gaithersburg, MD
20877
?
?
Dave, please see my post to Andy Nehan.
On 1/7/2022 9:30 AM, DAVE REISER wrote:
Same problem here.
?
Kind Regards,
Dave
Dave
Reiser
?
?
Purchased from Mirfield Electronics so it
should be good. Downloaded the TinySA app which works well
and connects to the device successfully. So far so good.
When I put the TinySA into DFU mode to initiate a firmware
update it promptly loses connection with the PC so firmware
upload is not therefore possible.
So I guess I am doing something wrong but cant figure out
what. I have watched Youtube videos but they have not
replicated the problem I am having.
Andy
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
Hi John,
?
Hallelujah, praise the Lord worked! The only thing I found different was you said that you checked the universal serial bus controllers for the boot loader. It was in the
universal serial bus devices not controllers.. That may be computer specific.
Anyway thank you very very much. If I get the chance I'll document that with pictures, a little bit more than what you did. If it's worth sharing I'll share it.
?
Kind Regards,
Dave
Dave Reiser
Phone:
301-216-5394
Mobile:
301-802-1929
Email:?
davereiser@...
520 Russell Avenue, Gaithersburg, MD 20877
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
john rader
Sent: Friday, January 7, 2022 2:42 PM
To: [email protected]
Subject: Re: [tinysa] Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC #tinysa
?
Dave, please see my post to Andy Nehan.
On 1/7/2022 9:30 AM, DAVE REISER wrote:
Same problem here.
?
Kind Regards,
Dave
Dave Reiser
?
?
Purchased from Mirfield Electronics so it should be good. Downloaded the TinySA app which works well and connects to the device successfully. So far so good.
When I put the TinySA into DFU mode to initiate a firmware update it promptly loses connection with the PC so firmware upload is not therefore possible.
So I guess I am doing something wrong but cant figure out what. I have watched Youtube videos but they have not replicated the problem I am having.
Andy
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
Dave, please see my post to Andy Nehan.
On 1/7/2022 9:30 AM, DAVE REISER wrote:
toggle quoted message
Show quoted text
Same problem here.
?
Kind Regards,
Dave
Dave Reiser
?
?
Purchased from Mirfield Electronics so it
should be good. Downloaded the TinySA app which works well and
connects to the device successfully. So far so good.
When I put the TinySA into DFU mode to initiate a firmware
update it promptly loses connection with the PC so firmware
upload is not therefore possible.
So I guess I am doing something wrong but cant figure out
what. I have watched Youtube videos but they have not
replicated the problem I am having.
Andy
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
Great stuff, that worked very well indeed.
toggle quoted message
Show quoted text
------ Original Message ------
From: "john rader" <jara8462@...>
To: [email protected]
Sent: Friday, 7 Jan, 2022 At 07:34
Subject: Re: [tinysa] Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC #tinysa
Andy, I just got my tinysa from amazon and everything worked as you describe. Had the same problem updating the firmware too, but finally got it upgraded.I tried the dfu demo and it wouldn't see the tinysa. Had to use stm32cube programmer as the dfu demo was superceeded by it. Could not get the dfu programmer in tinysa app to connect to it either. I reloader the defuse demo version 3.05 again, still could connect to tinysa by defuse demo ot tinysa app. I put the tinysa in dfu mode by menu, went to device manager, checked universal serial bus controllers, and verified that stm32 bootloader was present. Double clicked on it and went to driver tab, selected update driver on the internet, not on computer, waited until it finished and said driver was updated. I then started stm32 cube programmer, clicked on open file at top left, selected the location where I placed the update bin file in pop up , (be sure you changed the bin file to tinysa.bin), selected it and it loaded into the programmer, be sure sure it says usb configuration on top right of programmer, it will not have a port number but has usb1 and right below it says "serial number fffffffeffff". Click on download and it will then download the bin file to the tinysa. I have included a .jpg of how the programmer should look like, ignore the "not connected" at top right of programmer, when you select download it will do the connecting. Hope this helps you, you will have to download the stm32 cube programmer and install it first of course. john
On 1/6/2022 3:59 PM, ANDY NEHAN via groups.io wrote:
Purchased from Mirfield Electronics so it should be good. Downloaded the TinySA app which works well and connects to the device successfully. So far so good.
When I put the TinySA into DFU mode to initiate a firmware update it promptly loses connection with the PC so firmware upload is not therefore possible.
So I guess I am doing something wrong but cant figure out what. I have watched Youtube videos but they have not replicated the problem I am having.
Andy
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
You need a driver for the DFU mode, it is not the same as the
normal one used for serial coms with TinySA App.
There is a lot of info about it in previous messages.
Ignacio EB4APL
El 06/01/2022 a las 21:59, ANDY NEHAN
via groups.io escribió:
Purchased from Mirfield Electronics so it should be good.
Downloaded the TinySA app which works well and connects to the
device successfully. So far so good.
When I put the TinySA into DFU mode to initiate a firmware update
it promptly loses connection with the PC so firmware upload is not
therefore possible.
So I guess I am doing something wrong but cant figure out what. I
have watched Youtube videos but they have not replicated the
problem I am having.
Andy
_
|
Re: Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC
#tinysa
Same problem here.
?
Kind Regards,
Dave
Dave Reiser
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
ANDY NEHAN via groups.io
Sent: Thursday, January 6, 2022 4:00 PM
To: [email protected]
Subject: [tinysa] Firmware upgrade - put TinySA into DFU mode and it loses contact with the PC #tinysa
?
Purchased from Mirfield Electronics so it should be good. Downloaded the TinySA app which works well and connects to the device successfully. So far so good.
When I put the TinySA into DFU mode to initiate a firmware update it promptly loses connection with the PC so firmware upload is not therefore possible.
So I guess I am doing something wrong but cant figure out what. I have watched Youtube videos but they have not replicated the problem I am having.
Andy
|
DavidC KD4E
john rader
DAVE REISER WA3TRS