Re: No pulse on CAL when freq sweeping on signal generator
#tinysa
#ultra
Hi,?
The 2 channel SDS1000X-E does not support the Bode Plot, the 4 channel scope does. See page 236 of the owners manual.
Press the Utility button then go to to the second page. The Bode Plot selection is missing on the 2 channel scope.
I'm not sure if there has been a firmware update that makes a change to support the Bode Plot.
Richard?
Hi,
?
I wonder if I'm doing something wrong or my TinySA is misbehaving.
?
I want to use TinySA Ultra to align IF transformers by? visualising the freq attenuation (bode plot) on an oscilloscope.
?
However, the TinySA Ultra does not seem to output the sweep pulse on Cal output. I did checked the Pulse High option.
Below are pictures with scope output and TinySA settings.
?
Can anyone give me a clue?
?
|
No pulse on CAL when freq sweeping on signal generator
#tinysa
#ultra
Hi,
?
I wonder if I'm doing something wrong or my TinySA is misbehaving.
?
I want to use TinySA Ultra to align IF transformers by? visualising the freq attenuation (bode plot) on an oscilloscope.
?
However, the TinySA Ultra does not seem to output the sweep pulse on Cal output. I did checked the Pulse High option.
Below are pictures with scope output and TinySA settings.
?
Can anyone give me a clue?
?
|
Some of the new mini-pcs have USB ports that are not powered.
Joe
toggle quoted message
Show quoted text
On 5/18/2025 9:35 AM, Erik Kaashoek wrote: On Sun, May 18, 2025 at 01:36 AM, pa3cqn wrote:
Jus wondering: if you use the USB-C connection for serial isn't
the battery charging? So you are not losing but gaining mAh's?
Correct
--
Designer of the tinySA
For more info go to
|
On Sun, May 18, 2025 at 01:36 AM, pa3cqn wrote:
Jus wondering: if you use the USB-C connection for serial isn't the battery charging? So you are not losing but gaining mAh's?
Correct
--
Designer of the tinySA
For more info go to
|
Re: Hunting Spurious Emission at 154 MHz
On Sat, May 17, 2025 at 01:33 PM, David Platt wrote:
Another common source for RF noise in these VHF frequency ranges, is a bad cable-TV setup somewhere.
I seem to recall a particular problem was cable channel 52(?) coming up in the 2 meter band.
73, Don N2VGU
|
Jus wondering: if you use the USB-C connection for serial isn't the battery charging? So you are not losing but gaining mAh's?
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
When I search for a zk10 I get all kinds off stuff also. But when I search on zk10d I get the chip. Be adware that the results differ from country to country.?
?
I tried the link also, message "oeps does not deliver in your country".
?
Look at the price difference.
?
?
?
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
Link definitely works in Australia, but I then tried changing the delivery address to my daughters address in USA Ma, and it then said "Page not found"
You might need to have a conversation with your President.
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
|
Re: Hunting Spurious Emission at 154 MHz
My experience agrees with yours re MATV. I work in large stadiums, and it is unusual to monitor TV channels that should not be there "Over the Air" and indeed are not measurable when moving to different parts of the stadium.
It is currently especially prevalent as large screen MATV's in public areas are being replaced with IPTVs and little care is taken of the unterminated MATV coax, it's often just shoved back into the wall. In a large stadium it can be a two year project to migrate 100's of TV's add all the switches run CAT 6, all the time there are more and more unterminated Coax.
the dead giveaway is seeing Channel 27 with a 7MHz signal (Australia uses 7MHz TV channels) but 27 was never used Over the Air as it is 519-526MHz and Two-way Land Mobile Radios are 450-520MHz. (520-526MHz is really a guard band).
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
Seller sent me same link, and i guss it does not ship to my region. Aliexpress returns 404 for me.
On Sat, May 17, 2025 at 10:02 PM, Andrew Matros wrote:
They are listed -
I doubt you can use the BGA2817 instead. They have a different pinout, and the powering method is not the same either. In the GHz frequency range, any extra wiring can cause unpredictable results, so I would prefer to buy a proper chip and avoid the risk.
?
?
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
This one worked for me.
?
?
?
Don't forget there is a new $100 customs processing fee for all packages coming from overseas.? This is in addition to any tariffs.
?
Terry
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
What can I say? For me it popped up a tiny square "blue smoke" container that amplifies radio signals. Maybe try ZK10D. The point was that a quick search will solve the problem more quickly than a complaint posted to an internet group. Links posted by someone often don't work as intended for others for various reasons. But you don't need to fret about the reasons to find what you are looking for. On Sat, 17 May 2025 22:27:39 -0400 "Mike C. via groups.io" <mg@...> wrote: Really?? This is what comes up:
ZK10 Flashlight Box Tool Storage Case For 18650 Battery LED Flashlight
14500 Torch/Lamp Battery Charger Holder 5 Sizes Outdoor
Mike C. Sand Mtn GA
On 5/17/2025 5:51 PM, Jim Shorney via groups.io wrote:
Type ZK10 into the search box. -- 73 -Jim NU0C
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
That link works fine here in UK¡. Peter
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
Really?? This is what comes up:
ZK10
Flashlight Box Tool Storage Case For 18650 Battery LED Flashlight
14500 Torch/Lamp Battery Charger Holder 5 Sizes Outdoor
Mike C. Sand Mtn GA
On 5/17/2025 5:51 PM, Jim Shorney via
groups.io wrote:
toggle quoted message
Show quoted text
Type ZK10 into the search box.
On Sat, 17 May 2025 17:22:24 -0400
"Mike C. via groups.io" <mg@...> wrote:
That link does NOT work.
Mike C. Sand Mtn GA
On 5/17/2025 5:02 PM, Andrew Matros via groups.io wrote:
They are listed -
I doubt you can use the BGA2817 instead. They have a different pinout,
and the powering method is not the same either. In the GHz frequency
range, any extra wiring can cause unpredictable results, so I would
prefer to buy a proper chip and avoid the risk.
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
Type ZK10 into the search box. On Sat, 17 May 2025 17:22:24 -0400 "Mike C. via groups.io" <mg@...> wrote: That link does NOT work.
Mike C. Sand Mtn GA
On 5/17/2025 5:02 PM, Andrew Matros via groups.io wrote:
They are listed -
I doubt you can use the BGA2817 instead. They have a different pinout,
and the powering method is not the same either. In the GHz frequency
range, any extra wiring can cause unpredictable results, so I would
prefer to buy a proper chip and avoid the risk.
-- 73 -Jim NU0C
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
Very interesting. It works for Canada. But indeed? it does not work for USA, UK, France, Spain... 
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
That link does NOT work.
Mike C. Sand Mtn GA
On 5/17/2025 5:02 PM, Andrew Matros via
groups.io wrote:
toggle quoted message
Show quoted text
They are listed -
I doubt you can use the BGA2817 instead. They have a
different pinout, and the powering method is not the same
either. In the GHz frequency range, any extra wiring can cause
unpredictable results, so I would prefer to buy a proper chip
and avoid the risk.
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
They are listed -
I doubt you can use the BGA2817 instead. They have a different pinout, and the powering method is not the same either. In the GHz frequency range, any extra wiring can cause unpredictable results, so I would prefer to buy a proper chip and avoid the risk.
|
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA
#tinysa
#ultra
So.. I received LNA's (BGA2817), but it turns out i need Zeenko's ZK10D. They are not listed on theirs aliexpress store. I wrote them, waiting for answer.
Is there any way to bodge BGA2817 in there? Or maybe order some other part, that is easier to source?
|
Donald S Brant Jr
Terry W7AMI
Jim Shorney
Mike C.