开云体育

Hi, does anyone have any good resources? Other than echo Link to help me set levels for box on a repeat running echo Link? I do it by trial and error because I've never found a good resource to help me set that correctly, people say I'm cutting out all the time and people coming through my link for Peter seem to cut out a lot. I am going to get a West mountain radio rig blaster plug-in play next week which will maybe help that problem. But in the meantime, does anyone have any settings? Suggestions for my echo link note? Chad Nelson WI9HF/WRPL979 Janesville Wisconsin 608-754-8671 Send from my spectrum iPhone 16.

Anyone happen to have an assembly sheet for a AirCell/Trilogy NMP01250 Heliax Connector? Don't need the spec sheet. Just need the info to prep the end of the heliax. Rob K7TGU

Hello All. I am having issues programming a VHF DeskTrac Repeater and wanted some insights I've built close to 8 Different Cables all listed as "DeskTrac"or"MaxTrac" and I have not been able to get it to program I am using a RIB Box and switching the Blue 1, 2, and 3 switch on the DeskTrac the PC is running Windows XP With DosBox with the serial port Forwarded to Serial 1 (an actual Serial Port on the Laptop) sometimes the Data light will blink then start rapidly blinking but after like 1/2 a Second it just sits there with nothing and blinks every 1/2 - 1/4 of a second then the software goes Cannot read Data

Folks I had something odd here. I have three Quantars in service, all 100W, one UHF in 441 band, two 927 band. I had a PA fail on the 927 in Cedar Hill so for tight now I pulled the PA from the local Quantar here at the house and put it in Cedar Hill and that's all fine, 100W out. The 441 Quantar is here in the shack and easy to work on (its three feet away). So I popped out the UHF exciter and PA, installed a 900 exciter and one of my spare 900 PA's, reprogrammed the codeplug for 900 transmit, connected the 10 mhz out from my service monitor for external ref. All three PA's only would make 20 watts and all showed PA Fail and PA low. And to answer the first question, the PA out was connected directly to the Bird/load. Is there a difference between a UHF and 900 (or 800) chassis? I'm puzzled because when I popped one of these PAs into the 927 Quantar in the garage all was fine, no faults. Also in the uhf chassis they all showed just about zero reflected power. GeorgeC W2DB

I've searched the existing topics without finding what I need. I have an RC-100 that's working well, but I'd like to disable the base station timeout. I have worked with the tones, but it's been a couple of years. Can anyone help with the tone sequence? Any help would be muchly appreciated.

Looking to swap a brand new ics control quantar 1x for the northcomm quantar ecm and program cable. I'm looking for a more simple plug and play solution than something I need to jump through all sorts of gyration to get up and running. And I don't need all the capabilities of the ics I just need remote disable, and courtesy beep. So the northcomm might be better for me and the ics might be suited to someone who has more patience than i do to set it up properly and needs the advanced functionality of the ics. I'm only using this on a gmrs repeater so I don't need a bunch of advanced features or digital linking. My understanding is the northcomm is just set wildcards in quantar and then 1 adjustment on the board that requires no test gear to set it up. Suffice to say I can't get courtesy beep or remote disable to function on my quantar with the ics and the ics is brand new. I got voice id'er to work fine so I'm sure it's a setting on the ics board. I'm just out of patience to screw with it. I want an overall plug and play unit. I will also sell the ics outright for what i paid for it in leu of a swap. Let me be clear it's not ics fault it's l something I'm not doing correctly and I don't have the eyesight or dexterity in my hands anymore to work with small stuff like this board. Thanks Robert Chrysafis Kc8gpd Wrcm325 Scottsbluff NE

All, On batlabs's spectra page it mentions that there is an option on the analog spectra to do flat tx/rx audio which I need for some data purposes, It also mentions that hte info is in the service manual (the version I have its not) Does anyone know what jumpers need to be changed inside the radio to get flat tx/rx audio to the rear connector on a dash-mount radio? I'd also potentially be interested in a uhf service manual if anyone has one that they'd part with that has that information in it. Thanks --Don KD7WKF

does anyone have a programming lead for a kyodo kg510 or schematic of one

I had a TKR 750 working on a RLC 3 Controller. I bought a New TKR D710 and hooked it up to the same cable and configured the D710 just about Identical to the TKR 750. If I let the Repeaters internal controller control the Repeater I get normal Audio out of the repeater but when I turn off the Repeat enable and let the RLC control it I get PTT on the D710 but no Audio just Carrier I also have TKR 850 on another Port it will key up but no Audio and if I talk into the TKR 850 it repeats fine out of it but the D710 Transmits but no Audio out. I have Aux In/Out 4 Set to Encode Signaling Enable, Aux Out 5 COR Active Low and Aux In/Out 6 TOR Active Low. Ted McArthur kb7pab@... 435-770-9169 Callsigns AC7II _ Amateur D-451_Cache County Ecomm 59-A-40_State of Utah DEM WRJH-604_General Mobile Radio Service

I have available free for pickup three vhf Micor base stations. One of them has a 136-150mHz PA deck, that was working when last in service about ten years ago. There have been various parts robbed, but believe there is enough here that one complete repeater could be assembled. I believe there is a native 142-150mHz receiver as well. The collection comes with a set of NOS 8560 finals. Free for pickup in West Terre Haute, IN. You must take the entire lot. Contact me direct at k9hxATyahoo if interested. I do gave a few pictures, but the cabinets are against a wall, and are a little dirticult to move to get better shots. There are three loose HP power supplies, status unknown. Thanks and 73, Kevin, K9HX

Looking for Yaesu scu 20 for fusion if anyone has one for sale thanks n4jem

All, Have a nice UHF MTR-2000 40w we are looking to use for 44 ham usage. Starting from a clean default profile, it programs up perfectly and will operate perfectly. But if powered down, TX audio & CW ID are way down, etc. It's like it's losing settings. Reload the codeplug and it's back in business. Test menu every thing works perfectly, including deviation. I'm wondering if it's go an issue like the quantars with worn out non-volatile memory (EEPROM, E2PROM, or similar). Anyone dealt with this before? Any suggestions appreciated. This repeater is otherwise very nice and hears extremely well. Thanks in advance, Alan Barrow KM4BA

Looking for a Secure Capable Station Control Board for a UHF 100w MSF 5000, had an SCR smoke. Was also dealing with some occasional noise on the TX. TLN 3043B0818K. Any options would be welcome, and if you have the entire MSF5000 of similar model we might be interested in some other parts. Thanks, Alan Barrow KM4BA

I am building a Duplexer for a GMRS repeater. I have a Wacom WP-678 that is missing the interconnect cables. I did a little search hoping I could find some documentation on the lengths for cutting new ones. 462/467 split. Anyone know these off the top of their head, or have a chart somewhere? TNX Jim Sent from Outlook Virus-free.www.norton.com

Hi to All, I just bought a nice Motorola CDM-1250 Low-Band modified for 6 Meter Ham Band. But I am looking for the Service manual and I can only find the manual for VHF and UHF. The radio does work and turn on by the ignition accessories plug pin but I have some problem with the control head. No ON-Off button function, no Lights for the display, no RX-TX light, no Lightening of the DTMF Mike. And I have some question on the output power specs of this radio, it is set to 65 Watts in CPS put putting out 90 W on my Bird Bench Wattmeter? My Model is : AAM25DKD9AA2AN I am hoping that a member as seen this control heads problem before and somebody as the proper manual for this radio. Or at least the model number info to know what is the normal output power of this radio? Thanks’ to all for looking in their electronic document file. Best 73 Carl VA2CMB

hello everyone, well i am thinking of doing an Hard reset,,,or Factory rest for my VHF Low Split repeater.It was used on a commercial site so it must have some "special setup" so i am looking for the 2 files,The RX and the TX file of a working repeater,i would need only to change for my frequency! maybe someone could share it with me! i will appreciate the help, Tait are not known very much here ,we are in Motorola and Kenwook land!!! thanks a lot. 73/s Gervais,ve2ckn

Hi, I own a MTR2000 UHF Low Band High Power. Apparently there is a way to get this low band within the ham band (430-440). I once saw a description on the repeater-builder website but can't find anything about it anymore. Is there anyone who can help me on my way? Thanks in advance, Manu - ON7FQ