开云体育

Would anyone have handy the information for ordering the 15 pin molex plug on the back of these repeaters? It's labeled TEST/SPKR and is the ACC15P plug.

Thanks, Joe, K1ike

Here ya go

Ken


At 04:37 PM 10/23/2022, you wrote:

Would anyone have handy the information for ordering the 15 pin molex plug on the back of these repeaters? It's labeled TEST/SPKR and is the ACC15P plug.

Thanks, Joe, K1ike

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories
Phone: (503) 678 6182

Authorized Dealers for Kenwood and Telewave.
We offer complete turn-key repeater packages!
"We don't just make 'em. We use 'em!"
[]

If you read his email, I believe he is looking for a part number for the connector so he can purchase one.? "information for ordering"

Mick - W7CAT

Uh duh......


Yea, Molex discontinued the 15 pin but the KW part # is E37-0913-05 (connector and cable)



At 05:24 PM 10/23/2022, you wrote:

If you read his email, I believe he is looking for a part number for the connector so he can purchase one.? "information for ordering"

Mick - W7CAT

----- Original Message -----
From: "Ken Arck AH6LE"
To: [email protected]
Sent: Sunday, October 23, 2022 06:14:08 PM
Subject: Re: [repeater-builder] Kenwood TKR NXR series repeater molex plug info

Here ya go

Ken


At 04:37 PM 10/23/2022, you wrote:

Would anyone have handy the information for ordering the 15 pin
molex plug on the back of these repeaters? It's labeled TEST/SPKR
and is the ACC15P plug.

Thanks, Joe, K1ike

------------------------------------------------------------------------------

President and CTO - Arcom Controllers
Makers of repeater controllers and accessories
Phone: (503) 678 6182

Authorized Dealers for Kenwood and Telewave.
We offer complete turn-key repeater packages!
"We don't just make 'em. We use 'em!"
[]

--
Untitled Document

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories
Phone: (503) 678 6182

Authorized Dealers for Kenwood and Telewave.
We offer complete turn-key repeater packages!
"We don't just make 'em. We use 'em!"
[]

Thanks Ken,

I was afraid of that. I'll contact my Kenwood dealer and see if I can source a few of them.

Joe

The original Molex part number 03092158 has been replaced with 03092159.

The Molex .093 male crimp pins for 18-22 gauge wires is the 1380 series.

I have gotten the housings and pins from Digikey.

Joe - WA7JAW

At 10/23/2022 06:02 PM, you wrote:

Thanks Ken,

I was afraid of that. I'll contact my Kenwood dealer and see if I can
source a few of them.

I have said connector in front of me. I think most TKR/NXRs already have it as it contains a jumper to connect the front panel speaker to the radio.

The pins are .062 size & 0.145" pitch. Unfortunately they're no longer available beyond the 12 pin variety, but if you're lucky enough to already have the housing the .062" pins are widely available.

I did find this on eBay; I believe the plug is compatible with the TKRs.

<>

Bob NO6B

At 10/23/2022 09:17 PM, you wrote:

The original Molex part number 03092158 has been replaced with 03092159.

The Molex .093 male crimp pins for 18-22 gauge wires is the 1380 series.

The Kenwood accessory connector doesn't use .093" pins - they use .062".

Bob NO6B

Thanks to all,

I ordered a few from here last night.



I'll see what comes in the mail.

73, Joe, K1ike