开云体育

I have some copies of "220 Notes" articles from years ago. I'll look for them. I had a 13-509 repeater for years, and did some of the mods. As a matter of fact, that repeater is still alive & well

Hi All, I have a low band Mitrek radio, which is being used for our 10mtr repeater. I have got so far with it, but have come across a couple of problems which I need some help. On the 19 pin socket

Andrew, Here's a general run-down of all the voltages and what they go to: High Current Output: 13.1 to 16.3 VDC, with 36 amp load, and 2 amp load respectively Voltage is regulated *normally* only

This is true but the point was about relevance Dick WA3USH "It happens, just deal with it" The people will not understand the importance of the Second Amendment until it is too late." -- Thomas

Now what has that to do with ID?? If you listen to a broadcast station aqll ya hear is the main xmitter not the studio link either, which has as much relevance to this discussion as yer receiver

He is talking on one of his stations, the other is repeating him actually. Rules say EACH Amateur station must ID. Fact is there is no definition of a remote base in Part 97.

So listen to both transmitters with two receivers. You ID on the HT and hear the ID on the receiver listening to that transmitter. What do you hear on the receiver listening to the remote base? I'm

97.119 says in part: Each amateur station , except a space or telecommand station, must transmit it's assigned call sign on it's transmitting channel at the end - you know the rest so if a handheld

If you ID and add remote base to the end, you should be ok. Anyone else using it needs to do the same, or you will have to have a ID'er on it. 73, Daniel

You mean he has to give his callsign twice? Remember, he is talking on his own station, not someone else's. -------------------------------------- Richard Bomboy wrote:

Don't think so, he ID'ed the hand held station not the "base" station if what ya say is true a repeater does not need to ID either

Im looking for Mods on the Midland 13-509's ( aka Cobra 200, Clegg fm-76 ) . I know someone sent me the Sq. "mod fix" for it, but I had a HDD crash and lost it! ( yeah, my 90 day warranty on the

When you give your callsign over your HT, you just IDed your remote base. Chuck Kelsey WB2EDV ---------------------------------------------

In a message dated 4/26/99 12:16:43 AM Eastern Daylight Time, rlee@... writes: << If you listen to a broadcast station >> Now you're talking about two different sets of FCC rules

Actually it is pretty simple, if it xmits ya gotta ID it Dick WA3USH "It happens, just deal with it" The people will not understand the importance of the Second Amendment until it is too late." --

The 15.8v is with no load. Putting a 20amp load on it will only drop the voltage to ~15.0 volts. Under a mild load (2-5amps) the voltage stays around 15.6-.7 volts which seems a bit high to

In a message dated 4/25/99 10:40:43 PM Eastern Daylight Time, kelsey@... writes: << You mean he has to give his callsign twice? Remember, he is talking on his own station, not someone

In a message dated 4/25/99 10:00:51 PM Eastern Daylight Time, rlee@... writes: << Don't think so, he ID'ed the hand held station not the "base" station if what ya say is true a repeater does

I would like to operate a remoyte base from my house and I am confused as to the fcc requirements HOW or IF I need t ID the remote base. Can anyone help me? I am using a dual band mobile to

I just bought three samlex supplies from tech America when they had them on sale they were rated for 23 amps continuos but when I tried to run a UHF Maratrac mobile off it it would only make about 90