|
Re: GE Century II uhf mobile
Brent,
Well, I was going to try and crystal mine up for an uhf link radio. Pin outs
would really help! So would any tune up instructions you might have.
Thanks!
TD
By
Tracy585@...
·
#178
·
|
|
Re: GE phen.programable radios/info
kevin i was thinking about building a remote base out of a 261a kenwood.
would you happen to have any info on doing that I've built repeaters but
never a remote base,thank you. bill--k5py
By
bill <k5py@...>
·
#172
·
|
|
Re: GE phen.programable radios/info
kevin do you have any information on putting together a remote base.
I just never did that and i'am think about doing it. I think it would be fun
to do. thank you bill brown-----k5py.
By
bill <k5py@...>
·
#170
·
|
|
GE Century II uhf mobile
Brent,
Say, if you get a schematic, could I get a copy too? I've got one laying
around but I've never done anything with it for the same reason...
73
Tracy
By
Tracy585@...
·
#176
·
|
|
Re: GE phen.programable radios/info
"D.J.H." wrote:
Ok, I am not sure why you are only seeing message headers when html is
present. ??????
You can upgrade your Explorer to version 4.something for free
By
Kevin K. Custer W3KKC <kuggie@...>
·
#169
·
|
|
Re: GE phen.programable radios/info
Bill,
Tracy, K0DOE, here. I built a dual band remote using a Kenwood TW-4000A. Works
great! I used the controller momentary outputs to 'strobe' (ground) the mic
up/down switch for frequency change.
By
Tracy585@...
·
#173
·
|
|
Re: 222MHZ Micor repeater
In a message dated 2/15/99 9:47:10 PM Eastern Standard Time, kuggie@...
writes:
<< ve no experience with that exciter. I use the TLD 8732A
As far as the deviation goes, you should not have to
By
NE2E@...
·
#171
·
|
|
Re: GE phen.programable radios/info
Yes i can recive attachments,using microsoft exploder 3.02 i believe.
Doug
----------
By
D.J.H. <ve6zh@...>
·
#168
·
|
|
Welcome to the list.
Bill, K5PY wrote:
Hello Bill, and other recent subscribers.
Welcome to the list. A detailed explanation of the purpose and use
of this list is available
By
Kevin K. Custer W3KKC <kuggie@...>
·
#167
·
|
|
(No subject)
By
bill <k5py@...>
·
#166
·
|
|
Alinco SR4D Repeater controller
<html>
<body>
I am looking for anyone who has experience with the SR4D
repeater controller.
I am using one and I have been experiencing audio problems during the voice mail mode, and it also mutes the
By
S.Turner <n2kej@...>
·
#165
·
|
|
Large Heat Shrink Tubing
Hello All,
I recently received several requests from people on the list
wanting to obtain the large heat shrink I use to seal the Comet
and Diamond fiberglass antenna joints with. This stuff is
By
Kevin K. Custer W3KKC <kuggie@...>
·
#164
·
|
|
Re: X-500HNA
Ralph Hogan wrote:
I'll look up a retail vendor at work tomorrow (if I don't forget) If I don't
reply in the next couple of days, please email again.
I can send some to you.....although I would
By
Kevin K. Custer W3KKC <kuggie@...>
·
#163
·
|
|
Re: GE phen.programable radios/info
"D.J.H." wrote:
Can you receive html and attachments through your email server. Does the
browser you are using allow this?
Kevin
By
Kevin K. Custer W3KKC <kuggie@...>
·
#162
·
|
|
Re: Advice
JHowel@... wrote:
I'll build the NHRC4 for you.
By
Kevin K. Custer W3KKC <kuggie@...>
·
#161
·
|
|
Re: Advice
hmm 3 cavities may should work ok 2 on tx one on Rx
might be able to get about 60 db isolation 6 cavities 3 rx 3 tx u could obtain
100db isolation which will greatly improve the repeater
By
Brent DeSalvo KF4TNP <Bug1@...>
·
#159
·
|
|
Re: X-500HNA
We had a Diamond antenna (X-500HNA?)
machine for about two years. The antenna
eventually failed due to water ingress. I now heat shrink the joints before
installing this style antenna. I have
By
Ralph Hogan <rhogan@...>
·
#160
·
|
|
Re: GE phen.programable radios/info
Just fine!!
Doug
----------
----------------------------------------------------------
By
D.J.H. <ve6zh@...>
·
#158
·
|
|
Re: Advice
mch wrote:
Hi Joe,
Dan and I have a few of the Comet and Diamond antennas in duplex service.
Some are in crossband duplex, and some are in same band duplex with all
bands duplexed. Some are a
By
Kevin K. Custer W3KKC <kuggie@...>
·
#157
·
|
|
Re: Advice
Kevin K. Custer W3KKC wrote:
Kevin,
Do you (or anyone else) have any experience with the G6-270 (?) (the
dual-band G6) or the Comet antennas? This would be for relatively low
power duplex links. I
By
Joe M.
·
#153
·
|