开云体育

In a message dated 5/9/1999 6:04:27 PM Eastern Daylight Time, le067989@... writes: << how meny channels are these radio and what power and split thanks jim >> I have 2 of the 458 to 490,

Hi Again, I am looking for a duplexer, and when I check the specs for certain manufacturers, they state the " Transmitter noise suppression at receive frequency" and the "Receiver isolation at

Jeff here is the combination number mx65aag88a you can order manuals direct from GE at 800-446-7649 tom n8ies Jeff Weinberg W8CQ wrote:

You know, if you wanted to do some engineering of a circuit, you could make the repeater go to "sleep" periodically to save power. Pagers have been doing this for years. The receiver "wakes up"

I think these are the manuals you are looking for. To really nail it down, you need the combination number. LBI30250 Combination Manual LBI30215 Transmitter 8-20W LBI30211 Transmitter 21-40W LBI30207

I think these are the ones you are looking for. To really nail it down, you need the combination number. LBI30250 Combination Manual LBI30215 Transmitter 8-20W LBI30211 Transmitter 21-40W LBI30207

Hello Listmembers, I am in need for a set of manuals for a GE MASTR II UHF mobile unit. Can anyone supply me with the GE part numbers so I can order a set of manuals. Also, if someone would be willing

I own a vxr5000 uhf if you buy one make sure the tune it to the area of operation you want it for mine was to be used in the 460 area and the factory tuned it to the 450 area also they osilate to

Hi All, I have 2 Saber 1's for sale. Looking for $250.00 each. Please E-Mail for more info if needed. I would also consider trading these units towards UHF and VHF repeater equipment. Thanx Mike

I have a duplexed Motorola Mitrek 6 M repeater for sale. I think it is about a 75 watt unit, but may be more. It is already packed so I can't look at it to tell. It is already on frequency:

Looking for use feedback on Yaesu VXR-5000 and ICOM IC-RP1510. Looking to buy one of these, but have little info on them. 73's Lew K4hr@...

In a message dated 5/9/99 12:58:24 AM !!!First Boot!!!, k4hr@... writes: << Looking for use feedback on Yaesu VXR-5000 and ICOM IC-RP1510. Looking to buy one of these, but have little info on

The information you need is in GE manual number LBI4490. Unfortunately, I don't have the manual here, just the index. Duane

Looking For information on the GE DC CONTROL CARD Number PL19D417382G7 Rev. A that can be e-mailed to me. The Info that i am Looking for is the jumper configuration for the audio routing etc. Brent

ralph Thanks for the info and for the link to a good page. You may have sold me on the Micor. How is availability on the UHF micor vs. the UHF master II. Also since my #1 concern is power consumption.

Our MII draws around 200 mA. I don't know if that is typical or not. John AF4CY k4yd wrote:

Thanks for the help. I forgot to mention that I do not already have a Ge radio. I am looking to upgrade from a VHF Engineering machine before going to a mountain top. Does anyone have any suggestions.

k4yd wrote: Hi there. As for as the current draw on idle with the MasterII. You can drastically reduce the standby current draw by disabling the audio amplifier circuitry on terminal strip P904.

k4yd wrote: not the best rx for this use.... kiss a good .2 amp and add another .1 amp for the transmitter multiplier chain... yes it takes current in rx mode... we had a guy completely rebuild one

Does anyone know how much current a GE master II or master exec II draws in receive mode/ I need this info to calculate solar panel usage. k4yd