开云体育

The correct date was 9/24/ 2019. Len k4lfk ________________________________ Sent: Friday, February 19, 2021 5:34 PM To: [email protected] <[email protected]> Subject: Re:

I paid 46.76 pounds for the TX and RX VHF MSR2000 crystals with shipping on 9/42/2019. Len k4lfk ________________________________ Sent: Friday, February 19, 2021 5:24 PM To: [email protected]

QuartSLab prices for G.E. xtals went up over 70% in just 18 months, & that was as of a month ago. Maybe they went up another 20% since then? Bob NO6B

Years ago I ran a touch-tone function decoder on my Santiago Peak repeater that was fed by pre PL muted audio. No tone at all was required to send it a command. And since it didn't require PL to talk

* Thanks Jeff - but that would mean that normal repeat function would require a tone to get through - correct? Are you saying that you operate the repeater carrier-squelch? If so, then I'd do the

Here is something to think about also that may help. Look at the attached file. Rather than using a CTCSS decoder, I used the COR from the control radio. Mick - W7CAT

What Dan sezs. I've installed this at our main repeater site: https://www.ebay.com/itm/Repeater-Controller-Accessory-automation-Controller-8-Outputs-Relay-driver-DTMF/291330415500

Thanks Jeff - but that would mean that normal repeat function would require a tone to get through - correct? We do not want to do that either. I think from the several suggestions we have, adding

A good number of years ago I was using an RC850 controller and had a 220 MHz receiver feeding it for control.? DTMF never made it to any transmitter. Today you can buy a DTMF decoder for almost

Just use a separate receiver on another frequency and a DTMF controlled relay. There is a good unit that has 8 relays that is advertised in the back of every QST magazine. You can then connect that to

Unless I'm mis-remembering, you should be able to uncheck the box that says "Remote Access with QT/DQT" in the Remote Control screen. That will allow you to send DTMF to control the repeater without

Put in a second receiver on a different UHF channel within the pass band of your duplexor. Put a controller on it and there you go. It will drive them nuts when you control it and they can not hear a

I have the same problem here. There are a couple of pirate stations that have been occasionally showing up on my repeater. My response is to shut the repeater off for a while. My codes were originally

In had a set of Crystals made for my HT-220 from QuartSLab and they were $82 including shipping from the UK. Beautifully made and they have all the specs for Motorola radios. I installed them last

Hello, I have set up DTMF remote control for the TKR-750. The control commands are going to be repeated (and heard, copied by all users) when they are sent to the input frequency to remote control the

Since you already swapped VCOs and the problem continued, that points to the Uniboard. Other than swapping it with another one, I don't know how successful you'll be actually following the signals and

Might want to look at www.novexcomm.com ( http://www.novexcomm.com ) or at his ebay listings.?? They sell a rack panels for a single Bird 43 and another for a dual.? Or they can make whatever you

I'd always liked the idea of a directional coupler in line (perhaps TOR) to drive a device to display either linear (watts) or log (my preference) as a choice the tech can use.? Then perhaps as part

I used this it work well for antenna at the house for 6m. Also using this as my repeater antenna for 10m. W4BWW

They are a bit pricey, but I had good luck with the Array Solutions Power Master series watt meters. They will set the sensors for the frequency range you need, in addition to the HF units, I used