Re: Wacom WP-678 Cable lengths
- I have a Wacom WP-678 that is missing the interconnect cables.?
- ?
Is it a WP-678-R2 (two ports per cavity) or an original WP-678 (one port per cavity with a tee on top)? ? ??????????????????????????????????????????????????????????????????????????????? --- Jeff WN3A
|
Re: Swap: Ics controllers quantar 1x for a northcomm quantar ecm.
O may be able to help you out in your request. I have that plug and play controller. NASA courtesy time is nice and the repeater itself will ID.?
|
Re: General Dynamics R2600 Resouce CD Not Connecting
 Make sure that the communications analyzer is turned off until you are told to turn it on. Confirm the analyzer has completed startup before continuing with downloads. You can set communications parameters on the analyzer, but this should not be necessary, since holding the F1 key and waiting for four beeps sets the analyzer to 115200 bps, 8 data bits, 1 stop bit, no parity with Xon/Xoff handshaking. It is very important that you perform the analyzer startup properly. First, press and hold the F1 key on the analyzer. Then, turn on the analyzer and you will hear an immediate beep. Wait until you hear three beeps together in rapid succession and release the F1 key. At this point, the analyzer has begun to communicate with the PC
|
Re: General Dynamics R2600 Resouce CD Not Connecting
|
Thank you Mike, Jeff and Tim for all the info. ? Now I know that the normal output power is 60 Watts not 90 W like now. ? I will look at this manual to find the problem with my 1250 control head. ? At this point I don¡¯t know if the problem is created by the radio not suppling the correct voltage to the control heads. ? Or if the problem is in the control head. ? To be followed. ? Best 73 Carl VA2CMB ? De?: [email protected] [mailto:[email protected]] De la part de M M via groups.io
·¡²Ô±¹´Ç²â¨¦?: 14 avril 2025 02:17
??: [email protected]
Objet?: Re: [repeater-builder] Manual CDM Low-Band ? I forgot to say that the 6881091C63 Detailed Service Manual covers low band, high band and UHF... everything but the narrowband-only "200" and "700" MHz CDMs.?? They have their own manual.
Mike WA6ILQ
|
Tait TB7100 VHF,Hard reset and config file!!
hello everyone,
well i am thinking of doing an Hard reset,,,or Factory rest for my VHF Low Split repeater.It was used on a commercial site so it must have some "special setup" so i am looking for the 2 files,The RX and the TX file of a working repeater,i would need only to change for my frequency!
maybe someone could share it with me!
i will appreciate the help,
Tait are not known very much here ,we are in Motorola and Kenwook land!!!
?
thanks a lot.
73/s
Gervais,ve2ckn
?
|
Wacom WP-678 Cable lengths
I am building a Duplexer for a GMRS repeater.? I have a Wacom WP-678 that is missing the interconnect cables.? I did a little search hoping I could find some documentation on the lengths for cutting new ones.? 462/467 split.? Anyone know these off the top of their head, or have a chart somewhere? ? TNX Jim ? Sent from
|
He has the range 1 which won¡¯t go above 438. You can modify them. It might just be the resistive divider to tell the controller what it is but you might run out of vco range at some point. Been about five years since I tried this, memory hazy and ad usual I didn¡¯t document any of what I did?
?
georgec w2db?
?
|
Re: Tait TB7100 Vhf connection to the RB-USB RIM "Lite"!
hummm
many email ago someone tolded me that i add to used a Jumper on the repeater board when you are in "programmation" ,,,anyone remember what was that jumper???
i am still searching where is that DB25 pinout in the software!!!
i am almost ok,,,i have tx and audio when Allstar is starting but i am not heard by the Allstar audio,,,
gervais,,
Hello everyone,
i am trying to programm my TB7100 Vhf to worked with Scott RB-USB RIM "Lite".
Anyone has done it and if so maybe he could share the file of this repeater or
just a picture where i should go to set it up!
i am almost ok,my AllStar 2.0 is transmetting but it does not hear me but first i need to be sure the Tait is ok!
thanks in adavance for your help,
it will replace a simplex node here.
73/s
Gervais,ve2ckn
|
Hello Everyone, Am selling the below ham radio for a Silent key (AL0U) who has passed away. The rig are in excellent working condition and comes with accessories and original boxes. Kenwood TS-890, Kenwood SP-890 Speaker....Asking $2,650 shipped Icom IC-705 & AH-705 Tuner w/extras....Asking $1,300 shipped? Icom IC-7610.....Asking $2,550 plus shipping You can email me if you're interested in buying. Email: al5t.hamrig@...?
I'm also good on QRZ.COM
Am located in Alaska
?
Thanks
AL5T?
Robert
73's
|
Re: Decibel DB4060 Series Duplexers
Going thru my old notes, the 3.25 dimension corresponds to a loop part number -004.? ? ?The 3.50 dimension is a -005 loop.
?
-004 loops are standard for typical public safety band duplexers (nominally 155Mhz).
?
According to the article in repeaterbuilders, for the ham band, the high pass cans (notch low) should have a -005 loop and the low pass cans (notch high) should have a -004 loop. NOTE, the loops affect where the tuning CAP is adjusted to create the notch. From my experience, they don't significantly affect the band pass adjustment.
?
I've easily tuned cans from the public safety bands (all loops -004) without any problems. I guess it's possible changing one set of cans from -004 to -005 (make 1/4 in longer) could change the notch shape slightly BUT, those caps are VERY sensitive to soldering and I don't think the risk is worth changing the loop length without first trying using the public safety cans (with -004 loops).
?
?
?
?
?
|
T mobile had a $10/mo hot spot package of you paid for the Hotspot. It's not much data,? but enough for my dmr repeater.
toggle quoted message
Show quoted text
On April 14, 2025 12:44:14 PM CDT, "Jonny Tomlinson KF6PHX via groups.io" <jstlink@...> wrote:
if there is interet or wifi at the site...the little wyze cam v3 is awesome. We use them at mulitple sites and they work great and you can give access to multiple users if you want. Incredibly easy to setup.?? jonny? kf6phx
Hey Johnny, that's a good idea! You just gave me a really good idea for my repeater site that I'm gonna start to be using shortly. Should maybe find tiny surveillance camera and connect it up so I have monitoring capability visually. Just need
to figure out how to get it to transmit over the Internet to my location 60 miles away.
Chad Nelson WI9HF/WRPL979
Janesville Wisconsin
608-754-8671
Send from my spectrum iPhone 16.
On Apr 12, 2025, at 6:29?PM, Jonny Tomlinson KF6PHX via groups.io <jstlink@...> wrote:
?
No cameras?
Kf6phx
Sent from my Verizon, Samsung Galaxy smartphone
Get
Motorola VHF Quantar SN 509CLR1418
stolen from site last Thursday...
Along with DB4060B ...missing mounting brackets. Both tuned to 146.36/96 pair?
they cut the tie wraps holding the 4 cans together..the brackets had been misplaced but found and were to be reinstalled when repeater was discovered missing?
Also cables from rptr to duplexer and duplexer to Heliax gone....Sinclair Duplexer in cabinet that the rptr was sitting on not touched nor a UHF MII repeater...so this was personal....and I have 4 suspects in the list.
Sheriff's office has been contacted.
Contacting Boone Co Iowa (ironic) where the duplexer was bought from to get the SN on both units bought..lost the paperwork?
Chris WB5ITT?
--
Sent by morse code from my android K-9
|
Re: ICOM/RLC/CommSpec Items or Sale
I am interested in the TS-64 CTCSS encoder / decoders
I will purchase the 2 that you have.
Ron? ka3cnt@...
Did you sell all of the IC-901 stuff?
Thanks!
Scott N9AA
On 8/10/24 6:57 PM, Craig via wrote:
After further organizing my storage facility, I have found
the following items:
?
ICOM UX-59A 6M band unit for IC-900/901 - New and unused.?
ICOM UX-39A 220 band unit for IC-900/901 - New and unused.
ICOM UX-129A 1200MHz band unit for IC-900/901 - New and
unused
Asking $200 each plus shipping from 95762
?
RLC-ICM ICOM IC-900/901 Band Module Controller.? Includes 4
interface boards, ribbon cables and metal case - New and unused
Asking $200 plus shipping from 95762
?
CommSpec TS-32P CTCSS Encoder/Decoder? - New and unused - ( I
have 5 )
CommSpec TS-64 CTCSS Encoder/Decoder - New and unused - ( I
have 2 )
CommSpec DCS23 DTS Encoder/Decoder - New and unused ( I have
3, one without the manual )
Asking $50 each - Free Shipping
?
I accept Venmo or Zelle.? If interested, please PM me.
?
Thanks and 73,
Craig (AA6CG)
?
?
?
?
|
NXR-1800 ext MMDVM interface
Has anyone successfully interfaced an external MMDVM board to the RS-232 accessory connector on the Kenwood NXR repeater? I know the pinouts between the TKR-850/1 and the NXR appear identical in terms of what's required to tie to a MMDVM (the RB board for e.g), however I'm wondering if the NXR may be prone to audio phase distortion should it use a DSP based discriminator similar to a Quantar or XPR etc.
Anyone using one of these on DMR or P25 that can confirm it does or does not work with the external digital modem?
Regards
?
Kirb. VE6IV?
|
Re: Swap: Ics controllers quantar 1x for a northcomm quantar ecm.
The channel steering I'm not worried about. The quantar will only have a ch1. I just need remote disable and courtesy beep functions.
One thing to consider is if there is a power failure the Northcomm controller will revert to channel 1. You could put a small 5V backup battery on the Northcomm controller if power outages are a problem. Maybe use a 6V gel cell with a couple of diodes in series to drop the voltage to 5V and isolate it from the Quantar 5V bus.?
|
Re: Swap: Ics controllers quantar 1x for a northcomm quantar ecm.
One thing to consider is if there is a power failure the Northcomm controller will revert to channel 1. You could put a small 5V backup battery on the Northcomm controller if power outages are a problem. Maybe use a 6V gel cell with a couple of diodes in series to drop the voltage to 5V and isolate it from the Quantar 5V bus.?
|
Re: Swap: Ics controllers quantar 1x for a northcomm quantar ecm.
21 pages of wildcard settings but Northcomm supplies detailed instructions. Or I could probably send you a code plug from one of my Quantars with all the wildcards. Two adjustments to make, DTMF decode and courtesy beep level. If you program multiple channels you can then remotely dial up different channels with different power levels or PL tones or anything that can be programmed onto a different channel.?
|
Are they solely wireless with no hard wiring? And they're battery powered
I assume?
Ken
At 10:44 AM 4/14/2025, you wrote:
toggle quoted message
Show quoted text
if there is interet or wifi at
the site...the little wyze cam v3 is awesome. We use them at mulitple
sites and they work great and you can give access to multiple users if
you want. Incredibly easy to setup.?? jonny? kf6phx
From: [email protected]
<[email protected]> on behalf of Chad Nelson
<chad.nelson71@...>
Sent: Saturday, April 12, 2025 5:06 PM
To: [email protected]
<[email protected]>
Subject: Re: [repeater-builder] Be on the lookout
?
Hey Johnny, that's a good idea! You just gave me a really good idea for
my repeater site that I'm gonna start to be using shortly. Should maybe
find tiny surveillance camera and connect it up so I have monitoring
capability visually. Just need to figure out how to get it to transmit
over the Internet to my location 60 miles away.
Chad Nelson WI9HF/WRPL979
Janesville Wisconsin
608-754-8671
Send from my spectrum iPhone 16.
On Apr 12, 2025, at 6:29?€?PM,
Jonny Tomlinson KF6PHX via groups.io <jstlink@...>
wrote:
???
No cameras?
Kf6phx
Sent from my Verizon, Samsung Galaxy smartphone
Get
From: [email protected]
<[email protected]> on behalf of Chris Boone WB5ITT via
groups.io <setxtelecom@...>
Sent: Saturday, April 12, 2025 4:16:27 PM
To: [email protected]
<[email protected]>
Subject: [repeater-builder] Be on the lookout
?
Motorola VHF Quantar SN 509CLR1418
stolen from site last Thursday...
Along with DB4060B ...missing mounting brackets. Both tuned to 146.36/96
pair
they cut the tie wraps holding the 4 cans together..the brackets had been
misplaced but found and were to be reinstalled when repeater was
discovered missing
Also cables from rptr to duplexer and duplexer to Heliax gone....Sinclair
Duplexer in cabinet that the rptr was sitting on not touched nor a UHF
MII repeater...so this was personal....and I have 4 suspects in the
list.
Sheriff's office has been contacted.
Contacting Boone Co Iowa (ironic) where the duplexer was bought from to
get the SN on both units bought..lost the paperwork
Chris WB5ITT
------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories
Phone: (503) 678 6182
Authorized Dealers for Kenwood and Telewave.
We offer complete turn-key repeater packages!
"We don't just make 'em. We use 'em!"
![[]](http://www.arcomcontrollers.com/arcom.png)
|
if there is interet or wifi at the site...the little wyze cam v3 is awesome. We use them at mulitple sites and they work great and you can give access to multiple users if you want. Incredibly easy to setup.?? jonny? kf6phx
toggle quoted message
Show quoted text
Hey Johnny, that's a good idea! You just gave me a really good idea for my repeater site that I'm gonna start to be using shortly. Should maybe find tiny surveillance camera and connect it up so I have monitoring capability visually. Just need
to figure out how to get it to transmit over the Internet to my location 60 miles away.
Chad Nelson WI9HF/WRPL979
Janesville Wisconsin
608-754-8671
Send from my spectrum iPhone 16.
On Apr 12, 2025, at 6:29?PM, Jonny Tomlinson KF6PHX via groups.io <jstlink@...> wrote:
?
No cameras?
Kf6phx
Sent from my Verizon, Samsung Galaxy smartphone
Get
Motorola VHF Quantar SN 509CLR1418
stolen from site last Thursday...
Along with DB4060B ...missing mounting brackets. Both tuned to 146.36/96 pair?
they cut the tie wraps holding the 4 cans together..the brackets had been misplaced but found and were to be reinstalled when repeater was discovered missing?
Also cables from rptr to duplexer and duplexer to Heliax gone....Sinclair Duplexer in cabinet that the rptr was sitting on not touched nor a UHF MII repeater...so this was personal....and I have 4 suspects in the list.
Sheriff's office has been contacted.
Contacting Boone Co Iowa (ironic) where the duplexer was bought from to get the SN on both units bought..lost the paperwork?
Chris WB5ITT?
|
Swap: Ics controllers quantar 1x for a northcomm quantar ecm.
Looking to swap a brand new ics control quantar 1x for the northcomm quantar ecm and program cable.
I'm looking for a more simple plug and play solution than something I need to jump through all sorts of gyration to get up and?running.
And I don't need all the capabilities of the ics I just need remote disable, and courtesy beep.
So the northcomm might be better for me and the ics might be suited to someone who has more patience than i do to set it up properly and needs the advanced functionality of the ics.
I'm only using this on a gmrs repeater so I don't need a bunch of advanced features or digital linking.
My understanding is the northcomm is just set wildcards in quantar and then 1 adjustment on the board that requires no test gear to set it up.
Suffice to say I can't get courtesy beep or remote disable to function on my quantar with the ics and the ics is brand new. I got voice id'er to work fine so I'm sure it's a setting on the ics board. I'm just out of patience to screw with it.
I want an overall plug and play unit. I will also sell the ics outright for what i paid for it in leu of a swap.
Let me be clear it's not ics fault it's l something I'm not doing correctly and I don't have the eyesight or dexterity in my hands anymore to work with small stuff like this board.
Thanks
Robert Chrysafis
Kc8gpd
Wrcm325
Scottsbluff NE
|
Carl Beaudry
Gervais Fillion
AL5T Robert
Don Clark
Ken Arck AH6LE