开云体育

Someone asked me yesterday how to connect an Allstar node to a yaesu DR2X repeater, and mentioned they would like something plug-and-play. Is this product <https://www.customcomms.net/products> the

depending on which loops are in them. Jeff, I've attached a picture of the loop. From the connector to the end of the loop is 1.25" and about 1/2" wide. I've always used Sinclair equipment, so just

Telewave pass cavities, could be either VHF or UHF (3/4 wave) depending on which loops are in them. --- Jeff WN3A -- This email has been checked for viruses by Avast antivirus software. www.avast.com

Not 900 MHz at 24 inches in length. Jim W7RY -- Thanks and 73, Jim W7RY

They are Telewave VHF pass cans. Most likely from a Telewave VHF transmit combiner. Most older wide space transmit combiners used simple pass cavities. 73, Jim W7RY -- Thanks and 73, Jim W7RY

They look like the ones used on 900 Mhz paging transmitters. Probably tuned around 928 - 932 Mhz. Will handle a lot of power.

Can someone identify these cans? They are 24" tall and 10" in diameter. Both loops have "insertion loss" adjustments but no marking other than that. I haven't sweep one yet. Bench is a little full.

Many people are using the RIM-Maxtrac 9600 with CDM series radios for Winlink, both packet (1200 and 9600) and Vara FM (Narrow and Wide). Many Winlink Gateways are also using this configuration. The

The RIM Maxtrac and the RIM Alinco are the soundcards that connect your radio to your computer. I do not know for sure but you may be able to use them with Winlink. They are designed to be used with

I am going to pass on them as I have TMRD ( *too many radios disease)*. You should be able to find a collector that would want them. I am surprised that there are no pictures or articles about them. I

* I appreciate the write up Jeff! I’ll tune them up based on this and see if anything changes. Kevin sent me a private email which reminded me you had a Q2330E (six-cavity). For some reason I was

Yup - CloneZilla is not persnickety about which OS is on which drive. Its partition to partition function may be a bit tricky, but drive to drive is excellent and fast.? Just saved my Server 2016

Measure test cable losses by replacing the tee with a female-female barrel, then correct your insertion loss measurements based on that value when you’re adjusting the coupling with the tee

yes they are similar to an HT-220. These are on 171.210 Mhz. For further info please Mail me direct at: My call(at)rac.ca 73 John VE3AMZ Sent: Sunday, October 30, 2022 5:26 PM To:

I appreciate the write up Jeff! I’ll tune them up based on this and see if anything changes. I know I have each cavity currently set to 0.35db IL. I have an Amphenol Tee connector I’m using. Now,

Looking for information. I have a Motorola CDM1250 and all the programming software and cable.? I am looking at buying the RIM-Maxtrac.? Is this plug and play or what do I have to do. I also have a

I'll have to see if I still have a copy saved on my portable drives or on the server HD [email protected]> wrote:

Yes on Macrium, it requires you to have a licensed windows so that it borrows the PE boot from that installation to build the boot disk.? As long as the hardware in the computer will boot and be able

Anyone have a set of HKN9032A R1225 chassis to control head ribbon cables they would be willing to sell? Jeremy K1LFK

* So I guess my question is, at what tuning stage do I have to rotate the loops to set insertion loss. That’s the very first thing you do. From the factory, the loops would have been adjusted such