开云体育

if you log a station and after would like to post him on cluster you hit "Spot last QSO" then it past this info :

dx 2400.278 M0XUU?

but that is wrong format, it should be :

DX M0XUU 2400.278






73" OZ1CT Ben

Based on DX Spider specification, both variants are possible

Regards

Ladislav

ne 9. 6. 2024 v?14:14 odesílatel Bent Andersen via <eskolin=[email protected]> napsal:

if you log a station and after would like to post him on cluster you hit "Spot last QSO" then it past this info :

dx 2400.278 M0XUU?

but that is wrong format, it should be :

DX M0XUU 2400.278






73" OZ1CT Ben

ok Ladislav

I try this spot: dx 2400.209 OZ1IPU?

and it show up in "Console mode"

but it didn't?show?up in Spots mode "

my filer setup is here:

Den s?n. 9. jun. 2024 kl. 16.04 skrev ok1mlg via <ok1mlg=[email protected]>:

Based on DX Spider specification, both variants are possible

Regards

Ladislav

ne 9. 6. 2024 v?14:14 odesílatel Bent Andersen via <eskolin=[email protected]> napsal:

if you log a station and after would like to post him on cluster you hit "Spot last QSO" then it past this info :

dx 2400.278 M0XUU?

but that is wrong format, it should be :

DX M0XUU 2400.278






73" OZ1CT Ben

It is a little bit funny. I see two issues. The first issue is in QLog, because in case of "Split" mode, RX frequency should be reported, not TX. That will be fixed.

What is interesting is that I know DX Spider accepts 144.4 as 144.4 MHz, but I did not know that 2400.0 is not 2400.0 GHz but 2400.0 kHz. So, the specification is not very precise in this case. Based on the specification, it is possible to send frequencies in MHz, but this doesn't apply to GHz. This must be fixed in QLog too, but the DX Spider specification is pretty confusing.

Regards

Ladislav

ne 9. 6. 2024 v?16:37 odesílatel Bent Andersen via <eskolin=[email protected]> napsal:

ok Ladislav

I try this spot: dx 2400.209 OZ1IPU?

and it show up in "Console mode"

but it didn't?show?up in Spots mode "

my filer setup is here:

Den s?n. 9. jun. 2024 kl. 16.04 skrev ok1mlg via <ok1mlg=[email protected]>:

Based on DX Spider specification, both variants are possible

Regards

Ladislav

ne 9. 6. 2024 v?14:14 odesílatel Bent Andersen via <eskolin=[email protected]> napsal:

if you log a station and after would like to post him on cluster you hit "Spot last QSO" then it past this info :

dx 2400.278 M0XUU?

but that is wrong format, it should be :

DX M0XUU 2400.278






73" OZ1CT Ben

It is a little bit funny. I see two issues. The first issue is in QLog, because in case of "Split" mode, RX frequency should be reported, not TX. That will be fixed.

What is interesting is that I know DX Spider accepts 144.4 as 144.4 MHz, but I did not know that 2400.0 is not 2400.0 GHz but 2400.0 kHz. So, the specification is not very precise in this case. Based on the specification, it is possible to send frequencies in MHz, but this doesn't apply to GHz. This must be fixed in QLog too, but the DX Spider specification is pretty confusing.

Regards

Ladislav

ne 9. 6. 2024 v?16:37 odesílatel Bent Andersen via <eskolin=[email protected]> napsal:

ok Ladislav

I try this spot: dx 2400.209 OZ1IPU?

and it show up in "Console mode"

but it didn't?show?up in Spots mode "

my filer setup is here:

Den s?n. 9. jun. 2024 kl. 16.04 skrev ok1mlg via <ok1mlg=[email protected]>:

Based on DX Spider specification, both variants are possible

Regards

Ladislav

ne 9. 6. 2024 v?14:14 odesílatel Bent Andersen via <eskolin=[email protected]> napsal:

if you log a station and after would like to post him on cluster you hit "Spot last QSO" then it past this info :

dx 2400.278 M0XUU?

but that is wrong format, it should be :

DX M0XUU 2400.278






73" OZ1CT Ben